Arduino连接MPU6050陀螺仪
Posted punkrocker
tags:
篇首语:本文由小常识网(cha138.com)小编为大家整理,主要介绍了Arduino连接MPU6050陀螺仪相关的知识,希望对你有一定的参考价值。
一、线路连接
Arduino | MPU6050 |
VCC | 3.3V/5V |
GND | GND |
SCL | A5 |
SDA | A4 |
INT | D2 |
二、库下载
https://pan.baidu.com/s/1nvt75tJ
下载后,将相关库文件放进Arduino的libraries文件夹中
三、示例代码
// I2C device class (I2Cdev) demonstration Arduino sketch for MPU6050 class // 10/7/2011 by Jeff Rowberg <[email protected]> // Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib // // Changelog: // 2011-10-07 - initial release /* ============================================ I2Cdev device library code is placed under the MIT license Copyright (c) 2011 Jeff Rowberg Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. =============================================== */ // Arduino Wire library is required if I2Cdev I2CDEV_ARDUINO_WIRE implementation // is used in I2Cdev.h #include "Wire.h" // I2Cdev and MPU6050 must be installed as libraries, or else the .cpp/.h files // for both classes must be in the include path of your project #include "I2Cdev.h" #include "MPU6050.h" // class default I2C address is 0x68 // specific I2C addresses may be passed as a parameter here // AD0 low = 0x68 (default for InvenSense evaluation board) // AD0 high = 0x69 MPU6050 accelgyro; int16_t ax, ay, az; int16_t gx, gy, gz; #define LED_PIN 13 bool blinkState = false; void setup() // join I2C bus (I2Cdev library doesn‘t do this automatically) Wire.begin(); // initialize serial communication // (38400 chosen because it works as well at 8MHz as it does at 16MHz, but // it‘s really up to you depending on your project) Serial.begin(38400); // initialize device Serial.println("Initializing I2C devices..."); accelgyro.initialize(); // verify connection Serial.println("Testing device connections..."); Serial.println(accelgyro.testConnection() ? "MPU6050 connection successful" : "MPU6050 connection failed"); // configure Arduino LED for pinMode(LED_PIN, OUTPUT); void loop() // read raw accel/gyro measurements from device // accelgyro.getMotion6(&ax, &ay, &az, &gx, &gy, &gz); int16_t temp = accelgyro.getTemperature(); int16_t tempx = 21 + ( temp / 333.87 ); // these methods (and a few others) are also available //accelgyro.getAcceleration(&ax, &ay, &az); //accelgyro.getRotation(&gx, &gy, &gz); // display tab-separated accel/gyro x/y/z values Serial.print("a/g:\t"); // Serial.print(ax); Serial.print("\t"); // Serial.print(ay); Serial.print("\t"); // Serial.print(az); Serial.print("\t"); // Serial.print(gx); Serial.print("\t"); // Serial.print(gy); Serial.print("\t"); // Serial.println(gz); Serial.println(tempx); Serial.println("================================"); // blink LED to indicate activity blinkState = !blinkState; digitalWrite(LED_PIN, blinkState);
四、其他
1.其他方法可以在库文件的MPU6050.cpp中查看
2.温度传感器用于零漂校准,用于测温度不准
以上是关于Arduino连接MPU6050陀螺仪的主要内容,如果未能解决你的问题,请参考以下文章
Arduino ESP8266网页同步更新MPU6050数据模型化显示
STM32CubeMX(05) 移植陀螺仪MPU6050的DMP库读取三轴角度,加速度