不同vlan间的通信简单配置(三种方式)

Posted 大康

tags:

篇首语：本文由小常识网(cha138.com)小编为大家整理，主要介绍了不同vlan间的通信简单配置(三种方式)相关的知识，希望对你有一定的参考价值。

不同vlan间的通信简单配置

1．单臂路由(图)

环境：一台路由器，一台二层交换机，两台pc机
技术分享
 二层交换机的配置
一般模式：
Switch>
输入enable进入特权模式：
Switch>enable
输入configure terminal进入全局配置模式：
Switch#configure terminal 
Enter configuration commands, one per line.  End with CNTL/Z.
创建vlan 10 和 vlan 20：
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20
Switch(config-vlan)# exit
进入接口配置模式：
Switch(config)#interface fastEthernet 0/1
把0/1变成trunk口（默认是access口）
Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Switch(config-if)#exit
进入接口配置模式分别把对应的接口，加入对应的vlan：
Switch(config)#interface fastEthernet 1/1

Switch(config-if)#switchport mode access 
Switch(config-if)#switchport access vlan 10

Switch(config-if)#interface fastEthernet 2/1
Switch(config-if)#switchport mode access 
Switch(config-if)#switchport access vlan 20

到此而层交换机配置完毕！

路由器的配置：

Router>
Router>enable
Router#configure terminal 
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#inter fas 0/0

Router(config-if)#no ip address 
Router(config-if)#no shutdown

注意：单臂路由的配置父接口一定要no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up


Router(config-if)#exit

Router(config)#int fas 0/0.10

%LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up

Router(config-subif)#encapsulation dot1Q 10

注意：在配置ip时一定要先封装802.1q协议
Router(config-subif)#ip address 192.168.10.1 255.255.255.0
Router(config-subif)#no shutdown 
Router(config-subif)#int fas 0/0.20

%LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed state to up
Router(config-subif)#ip address 192.168.20.1 255.255.255.0

% Configuring IP routing on a LAN subinterface is only allowed if that
subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q,
or ISL vLAN.

Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip address 192.168.20.1 255.255.255.0
Router(config-subif)#no shutdown 
Router(config-subif)#

查看路由表：
Router#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.10.0/24 is directly connected, FastEthernet0/0.10
C    192.168.20.0/24 is directly connected, FastEthernet0/0.20
Router#

PC0的配置：
ip 192.168.10.10
netmask 255.255.255.0
gateway 192.168.10.1

PC1的配置：
ip 192.168.20.20
netmask 255.255.255.0
gateway 192.168.20.1

2.使用SVI实现VLAN间的通信（图）

环境：一台三层交换机，两台pc机

技术分享

三层交换机的配置：
Switch>enable 
Switch#configure terminal 
Enter configuration commands, one per line.  End with CNTL/Z.

创建vlan 10  20
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20
Switch(config-vlan)#exit

配置SVI接口ip
Switch(config)#interface vlan 10

%LINK-5-CHANGED: Interface Vlan10, changed state to up
Switch(config-if)#ip address 192.168.10.1 255.255.255.0
Switch(config-if)#no shutdown 
Switch(config-if)#interface vlan 20

%LINK-5-CHANGED: Interface Vlan20, changed state to up
Switch(config-if)#ip address 192.168.20.1 255.255.255.0
Switch(config-if)#no shutdown 
Switch(config-if)#exit

改变接口模式并加入vlan
Switch(config)#interface fastEthernet 0/1
Switch(config-if)#switchport mode access 
Switch(config-if)#switchport access vlan 10

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up
Switch(config-if)#interface fastEthernet 0/2
Switch(config-if)#switchport mode access 
Switch(config-if)#switchport access vlan 20

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up
Switch(config-if)#
看三层交换机的路由表：
Switch#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.10.0/24 is directly connected, Vlan10
C    192.168.20.0/24 is directly connected, Vlan20
Switch#
两主机的配置与单臂路由中两主机的配置一样

3.跨交换机实现VLAN间的通信（图）

环境：一台三层交换机，两台二层交换机，两台pc机

技术分享
三层交换机的配置(SW3)
Switch>enable
Switch#configure terminal 
Enter configuration commands, one per line.  End with CNTL/Z.

创建vlan 10 、 20 并设置ip
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20
Switch(config-vlan)#exit
Switch(config)#interface vlan 10

%LINK-5-CHANGED: Interface Vlan10, changed state to up
Switch(config-if)#ip address 192.168.10.1 255.255.255.0
Switch(config-if)#no shutdown 
Switch(config-if)#interface vlan 20

%LINK-5-CHANGED: Interface Vlan20, changed state to up
Switch(config-if)#ip address 192.168.20.1 255.255.255.0
Switch(config-if)#no shutdown 
Switch(config-if)#exit

设置接口模式并加入相应的vlan（注意trunk口的设置）
Switch(config)#interface fastEthernet 0/1

Switch(config-if)#switchport mode trunk

Switch(config-if)#interface fastEthernet 0/1
Switch(config-if)#switchport access vlan 10

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up

Switch(config)#interface fastEthernet 0/2
Switch(config-if)#switchport mode trunk 
Switch(config-if)#interface fastEthernet 0/2

Switch(config-if)#switchport access vlan 20

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up

Switch#

看路由表

Switch#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.10.0/24 is directly connected, Vlan10
C    192.168.20.0/24 is directly connected, Vlan20

SW21的配置
Switch>enable

Switch#configure  terminal 
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#exit

Switch(config)#interface fastEthernet 0/1

Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Switch(config-if)#interface fastEthernet 1/1
Switch(config-if)#switchport mode access 
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#

SW22的配置
Switch>

Switch>en

Switch#
Switch#configure ter
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#inter fas  1/1
Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to up


Switch(config-if)#switchport mode access  
Switch(config-if)#inter fas 2/1
Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/1, changed state to up
 
Switch(config-if)#exit
Switch(config)#vlan 20
Switch(config-vlan)#inter fas  1/1
Switch(config-if)#switchport access vlan 20
Switch(config-if)#

注意：两交换机之间的链接是trunk链路

4.以上配置在模拟器上都可实现

在模拟器上配置其中pc图片

上述三种方式pc机的配置都一样

技术分享 

技术分享 

验证：

技术分享

技术分享






































































































































以上是关于不同vlan间的通信简单配置(三种方式)的主要内容，如果未能解决你的问题，请参考以下文章

思科三层交换机配置实现不同vlan间的通信

怎么使用三层交换机使两台机器实现不同VLAN间的通信

如何实现不同vlan，不同网关的终端间的通信

对比如下三种方式实现Vlan之间通信的利与弊

VLAN之间单臂路由通信

配置简单的单臂路由实现网络通信