h3c端口聚合命令

Posted 2023-05-11

求h3c端口聚合命令，帮人家作业

创建聚合端口：
[Switch] interface bridge-aggregation interface-number
讲以太网口加入到聚合组里：
[Switch-Ethernet1/0/1] port link-aggregation group number 参考技术A 1．建立汇聚组
[SwitchA]link-aggregation group 1 mode manual
2．进入端口E1/0/1
[SwitchA]interface Ethernet1/0/1
3．参与端口汇聚的端口必须工作在全双工模式
[SwitchA-Ethernet1/0/1]duplex full
4．参与端口汇聚的端口工作速率必须一致
[SwitchA-Ethernet1/0/1]speed 100
5．将端口加入汇聚组
[SwitchA-Ethernet1/0/1]port link-aggregation group 1另一个端口做同样的配置。
静态汇聚的配置：
1．创建静态汇聚组1
[SwitchA] link-aggregation group 1 mode static
2．将以太网端口Ethernet1/0/1至Ethernet1/0/2加入汇聚组1
[SwitchA] interface Ethernet1/0/1
[SwitchA-Ethernet1/0/1] port link-aggregation group 1
[SwitchA-Ethernet1/0/1] interface Ethernet1/0/2
[SwitchA-Ethernet1/0/2] port link-aggregation group 1
动态汇聚的配置：
1．开启以太网端口Ethernet1/0/1至Ethernet1/0/3的LACP协议
<SwitchA> system-view
[SwitchA] interface Ethernet1/0/1
[SwitchA-Ethernet1/0/1] lacp enable
[SwitchA-Ethernet1/0/1] interface Ethernet1/0/2
[SwitchA-Ethernet1/0/2] lacp enable
[

H3C命令5

5、链路聚合配置

     链路聚合（Link Aggregation）又称Trunk，是指将多个物理端口捆绑在一起，成为一个逻辑端口，以实现出/ 入流量在各成员端口中的负荷分担，交换机根据用户配置的端口负荷分担策略决定报文从哪一个成员端口发送到对端的交换机。当交换机检测到其中一个成员端口的链路发生故障时，就停止在此端口上发送报文，并根据负荷分担策略在剩下链路中重新计算报文发送的端口，故障端口恢复后再次重新计算报文发送端口。链路聚合在增加链路带宽、实现链路传输弹性和冗余等方面是一项很重要的技术。 
[DeviceA] link-aggregation group 1 mode manual     ；创建手工聚合组1 
[DeviceA] interface ethernet 1/0/1                             ；将以太网端口Ethernet1/0/1加入聚合组1 
[DeviceA-Ethernet1/0/1] port link-aggregation group 1

“Can not specify a loopback-detection enable port as aggregation group member ! ”回环检测  
[DeviceA -Ethernet1/0/1]undo loopback-detection enable

[DeviceA-Ethernet1/0/1] port link-aggregation group 1  
[DeviceA] interface ethernet 1/0/2              ；将以太网端口Ethernet1/0/2加入聚合组1 
[DeviceA-Ethernet1/0/2] port link-aggregation group 1 
[DeviceA] link-aggregation group 1 service-type tunnel # 在手工聚合组的基础上创建Tunnel业务环回组。 
[DeviceA] interface ethernet 1/0/1      # 将以太网端口Ethernet1/0/1加入业务环回组。 
[DeviceA-Ethernet1/0/1] undo stp 
[DeviceA-Ethernet1/0/1] port link-aggregation group 1