H3C和CISCO交换机做聚合配置实例教学

Posted 2023-05-11

tags:

篇首语：本文由小常识网(cha138.com)小编为大家整理，主要介绍了H3C和CISCO交换机做聚合配置实例教学相关的知识，希望对你有一定的参考价值。

参考技术A

H3C和CISCO交换机做聚合配置实例教学

　　端口聚合也叫做以太通道，主要用于交换机之间连接。那么两种不同的交换机怎么做聚合配置呢?下面跟我一起来看看H3C和CISCO交换机做聚合配置实例教程，希望对同学们学习交换机有所帮助!

　　一、网络环境

　　本网络是xx大厦，3台交换机做端口聚合的课题

　　网络环境：H3C_A交换机<----------------->H3C_B交换机<----- ----------------------->cisco(3560)交换机

　　H3C_B交换机做为中心交换机

　　由于带宽需要，加上该9楼上了很多美国著名的avocentKVM的监控设备，需要很大的带宽，因此做了4组的端口链路聚合的需要

　　因此以下配置命令

　　1、H3C_A的.配置如下：(动态链路聚合，LACP默认启动)

　　[H3C_A]sys

　　[H3C_A]int bridge-aggregation 1

　　[H3C_A]link-aggregation mode dynamil

　　[H3C_A]int giabthernet1/0/26

　　[H3C_A_giabthernet1/0/26]duplex full

　　[H3C_A_giabthernet1/0/26]speed 1000

　　[H3C_A_giabthernet1/0/26]port link-type trunk

　　[H3C_A_giabthernet1/0/26]port trunk permit vlan all

　　因此，其它三个端口都是一样，如以上配置就可以了，同时H3C_B也是同样如H3C_A的配置一样，配好了，检查下端口的问题。

　　2、思科的配置

　　[cisco]int port-channel 2

　　[cisco]swit trunk encapsulation dot1q

　　[cisco]swit mode trunk

　　[cisco]swit trunk allowed vlan all

　　[cisco]进入端口模式配置

　　[cisco]int gig0/19

　　[cisco]duplex full

　　[cisco]speed 1000

　　[cisco]swit trun encapsulation dot1q

　　[cisco]swit mode trunk

　　[cisco]swit trunk allowed vlan all

　　[cisco]channel-group 2 mode active

　　其它的端口同样的配置

　　配置好了

　　在H3C交换机用 dis link-aggregation summary查看信息

　　同时，在思科交换机用show ethernetchannel summary查看信息

　　最后经过上面的配置，端口聚合就可以通了。

;

Cisco 的基本配置实例之四----vlan的规划及配置（核心交换机）

4、vlan的规划及配置

在本节中我们讲解vlan的规划及具体的配置命令。在此例中我们用的是vtp（VLAN Trunking Protocol）server的模式，在这种模式中我们需要配置核心交换机的vtp模式为server，各接入交换机的vtp模式为cilent，那么配置完成后接入交换机就会通过trunk口自动从核心交换机学习到所有的vlan配置信息。在接入交换机中只需要添加相应的端口即可，这样易于管理与部署。具体的配置命令我们通过两小节来演示：

4.1 核心交换机的相关配置

（这是一台已经配置好了的交换机，但这并不会影响我们的演示效果。所有我们新作的配置会在演示结束后清除。）

TEST#sh vlan # 显示已经有的vlan信息，并且同时显示了各端口所属的vlan

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Gi1/2, Gi1/3, Gi1/4, Gi1/5, Gi1/6, Gi1/7, Gi1/8, Gi1/9, Gi1/10, Gi1/11, Gi1/13, Gi1/14, Gi1/16, Gi1/17, Gi1/18, Gi1/19, Gi1/20, Gi3/12, Gi3/13, Gi3/16

2 firewall active Gi1/1

10 Engineering active Gi3/9, Gi3/10

20 Procurement active Gi3/19

30 QAQC active

40 Operation active

50 Yard active Gi3/18

60 BM active

70 HRAD active

80 Facility active

100 Finance active

110 GO active

120 Wlan active

150 Server active Gi3/1, Gi3/2, Gi3/3, Gi3/4, Gi3/5, Gi3/6, Gi3/7, Gi3/8

160 Client active Gi3/11, Gi3/15

# 从这行往下是为其他协议预留的vlan号段，这些不必理会。

1002 fddi-default act/unsup 1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1 enet 100001 1500 - - - - - 0 0

2 enet 100002 1500 - - - - - 0 0

10 enet 100010 1500 - - - - - 0 0

20 enet 100020 1500 - - - - - 0 0

30 enet 100030 1500 - - - - - 0 0

40 enet 100040 1500 - - - - - 0 0

50 enet 100050 1500 - - - - - 0 0

60 enet 100060 1500 - - - - - 0 0

70 enet 100070 1500 - - - - - 0 0

80 enet 100080 1500 - - - - - 0 0

100 enet 100100 1500 - - - - - 0 0

110 enet 100110 1500 - - - - - 0 0

120 enet 100120 1500 - - - - - 0 0

150 enet 100150 1500 - - - - - 0 0

160 enet 100160 1500 - - - - - 0 0

1002 fddi 101002 1500 - - - - - 0 0

1003 tr 101003 1500 - - - - - 0 0

1004 fdnet 101004 1500 - - - ieee - 0 0

TEST#conf

Configuring from terminal, memory, or network [terminal]? t

Enter configuration commands, one per line. End with CNTL/Z.

TEST(config)#vlan 200 # 我们新建一个vlan号为200的vlan

TEST(config-vlan)#name test # 给这个vlan命名，这样便于日常的管理。

TEST(config-vlan)#?

VLAN configuration commands:

are Maximum number of All Route Explorer hops for this VLAN (or zero if none specified)

backupcrf Backup CRF mode of the VLAN

bridge Bridging characteristics of the VLAN

exit Apply changes, bump revision number, and exit mode

media Media type of the VLAN

mtu VLAN Maximum Transmission Unit

name Ascii name of the VLAN # 刚才我们就是用的这条命令

no Negate a command or set its defaults

parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs

private-vlan Configure a private VLAN

remote-span Configure as Remote SPAN VLAN

ring Ring number of FDDI or Token Ring type VLANs

said IEEE 802.10 SAID

shutdown Shutdown VLAN switching

state Operational state of the VLAN

ste Maximum number of Spanning Tree Explorer hops for this VLAN (or zero if none specified)

stp Spanning tree characteristics of the VLAN

tb-vlan1 ID number of the first translational VLAN for this VLAN (or zero if none)

tb-vlan2 ID number of the second translational VLAN for this VLAN (or zero if none)

TEST(config-vlan)#END # 建好vlan后退出到特权模式中

TEST#show ip int brief

# 显示目前有的端口配置状态，我们会发现此时并没有vlan200的相关信息

Interface IP-Address OK? Method Status Protocol

FastEthernet1 unassigned YES NVRAM down down

Vlan1 192.168.113.254 YES NVRAM up up

Vlan2 172.16.0.2 YES NVRAM up up

Vlan10 192.168.101.254 YES NVRAM up up

Vlan20 192.168.102.254 YES NVRAM up up

Vlan30 192.168.103.254 YES NVRAM up up

Vlan40 192.168.104.254 YES NVRAM up up

Vlan50 192.168.105.254 YES NVRAM up up

Vlan60 192.168.106.254 YES NVRAM up up

Vlan70 192.168.107.254 YES NVRAM up up

Vlan80 192.168.108.254 YES NVRAM up up

Vlan100 192.168.110.254 YES NVRAM up up

Vlan110 192.168.111.254 YES NVRAM up up

Vlan120 192.168.112.254 YES NVRAM up up

Vlan150 192.168.100.254 YES NVRAM up up

Vlan160 192.168.115.254 YES NVRAM up up

GigabitEthernet1/1 unassigned YES unset up up

GigabitEthernet1/2 unassigned YES unset down down

GigabitEthernet1/3 unassigned YES unset down down

GigabitEthernet1/4 unassigned YES unset down down

GigabitEthernet1/5 unassigned YES unset down down

GigabitEthernet1/6 unassigned YES unset down down

GigabitEthernet1/7 unassigned YES unset down down

GigabitEthernet1/8 unassigned YES unset down down

GigabitEthernet1/9 unassigned YES unset down down

GigabitEthernet1/10 unassigned YES unset down down

GigabitEthernet1/11 unassigned YES unset down down

GigabitEthernet1/12 unassigned YES unset down down

GigabitEthernet1/13 unassigned YES unset down down

GigabitEthernet1/14 unassigned YES unset down down

GigabitEthernet1/15 unassigned YES unset up up

GigabitEthernet1/16 unassigned YES unset down down

GigabitEthernet1/17 unassigned YES unset down down

GigabitEthernet1/18 unassigned YES unset down down

GigabitEthernet1/19 unassigned YES unset down down

GigabitEthernet1/20 unassigned YES unset down down

GigabitEthernet3/1 unassigned YES unset up up

GigabitEthernet3/2 unassigned YES unset up up

GigabitEthernet3/3 unassigned YES unset up up

GigabitEthernet3/4 unassigned YES unset up up

GigabitEthernet3/5 unassigned YES unset up up

GigabitEthernet3/6 unassigned YES unset up up

GigabitEthernet3/7 unassigned YES unset up up

GigabitEthernet3/8 unassigned YES unset down down

TEST#sh vlan # 显示一下vlan信息

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Gi1/2, Gi1/3, Gi1/4, Gi1/5, Gi1/6, Gi1/7, Gi1/8, Gi1/9, Gi1/10, Gi1/11, Gi1/13, Gi1/14, Gi1/16, Gi1/17, Gi1/18, Gi1/19, Gi1/20, Gi3/12, Gi3/13, Gi3/16

2 firewall active Gi1/1

10 Engineering active Gi3/9, Gi3/10

20 Procurement active Gi3/19

30 QAQC active

40 Operation active

50 Yard active Gi3/18

60 BM active

70 HRAD active

80 Facility active

100 Finance active

110 GO active

120 Wlan active

150 Server active Gi3/1, Gi3/2, Gi3/3, Gi3/4, Gi3/5, Gi3/6, Gi3/7, Gi3/8

160 Client active Gi3/11, Gi3/15

200 test active

# 这个是我们新建好的vlan，但是vlan中没有任何端口。

1002 fddi-default act/unsup

1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1 enet 100001 1500 - - - - - 0 0

2 enet 100002 1500 - - - - - 0 0

10 enet 100010 1500 - - - - - 0 0

20 enet 100020 1500 - - - - - 0 0

30 enet 100030 1500 - - - - - 0 0

40 enet 100040 1500 - - - - - 0 0

50 enet 100050 1500 - - - - - 0 0

60 enet 100060 1500 - - - - - 0 0

70 enet 100070 1500 - - - - - 0 0

80 enet 100080 1500 - - - - - 0 0

100 enet 100100 1500 - - - - - 0 0

110 enet 100110 1500 - - - - - 0 0

120 enet 100120 1500 - - - - - 0 0

150 enet 100150 1500 - - - - - 0 0

160 enet 100160 1500 - - - - - 0 0

200 enet 100200 1500 - - - - - 0 0

1002 fddi 101002 1500 - - - - - 0 0

TEST#conf t

Enter configuration commands, one per line. End with CNTL/Z.

TEST(config)#interface gigabitEthernet 1/2

# 我们进入端口配置模式，配置gigabitEthernet 1/2这个端口

TEST(config-if)#switchport access vlan 200 # 将此端口加入到刚才建好的vlan200中

TEST(config-if)#end

TEST#sh vlan # 退出来验证一下

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Gi1/3, Gi1/4, Gi1/5, Gi1/6, Gi1/7, Gi1/8, Gi1/9, Gi1/10, Gi1/11, Gi1/12, Gi1/14, Gi1/16, Gi1/17, Gi1/18, Gi1/19, Gi1/20, Gi3/12, Gi3/13, Gi3/14

2 firewall active Gi1/1

10 Engineering active Gi3/9, Gi3/10

20 Procurement active Gi3/19

30 QAQC active

40 Operation active

50 Yard active Gi3/18

60 BM active

70 HRAD active

80 Facility active

100 Finance active

110 GO active

120 Wlan active

150 Server active Gi3/1, Gi3/2, Gi3/3, Gi3/4, Gi3/5, Gi3/6, Gi3/7, Gi3/8

160 Client active Gi3/11, Gi3/15

200 test active Gi1/2

# 现在GI1/2这个端口已经属于vlan200了。

1002 fddi-default act/unsup

1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1 enet 100001 1500 - - - - - 0 0

2 enet 100002 1500 - - - - - 0 0

10 enet 100010 1500 - - - - - 0 0

20 enet 100020 1500 - - - - - 0 0

30 enet 100030 1500 - - - - - 0 0

40 enet 100040 1500 - - - - - 0 0

50 enet 100050 1500 - - - - - 0 0

60 enet 100060 1500 - - - - - 0 0

70 enet 100070 1500 - - - - - 0 0

80 enet 100080 1500 - - - - - 0 0

100 enet 100100 1500 - - - - - 0 0

110 enet 100110 1500 - - - - - 0 0

120 enet 100120 1500 - - - - - 0 0

150 enet 100150 1500 - - - - - 0 0

160 enet 100160 1500 - - - - - 0 0

200 enet 100200 1500 - - - - - 0 0

1002 fddi 101002 1500 - - - - - 0 0

1003 tr 101003 1500 - - - - - 0 0

TEST#sh ip int brief

# 再显示一下所有端口的状态，我们会发现同样没有vlan200的相关信息。

Interface IP-Address OK? Method Status Protocol

FastEthernet1 unassigned YES NVRAM down down

Vlan1 192.168.113.254 YES NVRAM up up

Vlan2 172.16.0.2 YES NVRAM up up

Vlan10 192.168.101.254 YES NVRAM up up

Vlan20 192.168.102.254 YES NVRAM up up

Vlan30 192.168.103.254 YES NVRAM up up

Vlan40 192.168.104.254 YES NVRAM up up

Vlan50 192.168.105.254 YES NVRAM up up

Vlan60 192.168.106.254 YES NVRAM up up

Vlan70 192.168.107.254 YES NVRAM up up

Vlan80 192.168.108.254 YES NVRAM up up

Vlan100 192.168.110.254 YES NVRAM up up

Vlan110 192.168.111.254 YES NVRAM up up

Vlan120 192.168.112.254 YES NVRAM up up

Vlan150 192.168.100.254 YES NVRAM up up

Vlan160 192.168.115.254 YES NVRAM up up

GigabitEthernet1/1 unassigned YES unset up up

GigabitEthernet1/2 unassigned YES unset down down

GigabitEthernet1/3 unassigned YES unset down down

GigabitEthernet1/4 unassigned YES unset down down

GigabitEthernet1/5 unassigned YES unset down down

GigabitEthernet1/6 unassigned YES unset down down

GigabitEthernet1/7 unassigned YES unset down down

GigabitEthernet1/8 unassigned YES unset down down

GigabitEthernet1/9 unassigned YES unset down down

GigabitEthernet1/10 unassigned YES unset down down

GigabitEthernet1/11 unassigned YES unset down down

GigabitEthernet1/12 unassigned YES unset down down

GigabitEthernet1/13 unassigned YES unset down down

GigabitEthernet1/14 unassigned YES unset down down

GigabitEthernet1/15 unassigned YES unset up up

GigabitEthernet1/16 unassigned YES unset down down

GigabitEthernet1/17 unassigned YES unset down down

GigabitEthernet1/18 unassigned YES unset down down

GigabitEthernet1/19 unassigned YES unset down down

GigabitEthernet1/20 unassigned YES unset down down

GigabitEthernet3/1 unassigned YES unset up up

GigabitEthernet3/2 unassigned YES unset up up

GigabitEthernet3/3 unassigned YES unset up up

GigabitEthernet3/4 unassigned YES unset up up

GigabitEthernet3/5 unassigned YES unset up up

GigabitEthernet3/6 unassigned YES unset up up

GigabitEthernet3/7 unassigned YES unset up up

GigabitEthernet3/8 unassigned YES unset down down

TEST#conf t

Enter configuration commands, one per line. End with CNTL/Z.

TEST(config)#int vlan 200 # 给这个vlan添加相应的ip地址，注意此处的语法

TEST(config-if)#ip add 10.10.10.0.1 255.255.255.0 # 添加具体的ip地址

TEST(config-if)#no shut # 使能此端口

TEST(config-if)#end

TEST#sh ip int b

# 重新显示一下所有端口的状态，我们会发现已经有了vlan200的端口信息了。

Interface IP-Address OK? Method Status Protocol

FastEthernet1 unassigned YES NVRAM down down

Vlan1 192.168.113.254 YES NVRAM up up

Vlan2 172.16.0.2 YES NVRAM up up

Vlan10 192.168.101.254 YES NVRAM up up

Vlan20 192.168.102.254 YES NVRAM up up

Vlan30 192.168.103.254 YES NVRAM up up

Vlan40 192.168.104.254 YES NVRAM up up

Vlan50 192.168.105.254 YES NVRAM up up

Vlan60 192.168.106.254 YES NVRAM up up

Vlan70 192.168.107.254 YES NVRAM up up

Vlan80 192.168.108.254 YES NVRAM up up

Vlan100 192.168.110.254 YES NVRAM up up

Vlan110 192.168.111.254 YES NVRAM up up

Vlan120 192.168.112.254 YES NVRAM up up

Vlan150 192.168.100.254 YES NVRAM up up

Vlan160 192.168.115.254 YES NVRAM up up

Vlan200 10.10.0.1 YES manual up up

GigabitEthernet1/1 unassigned YES unset up up

GigabitEthernet1/2 unassigned YES unset down down

GigabitEthernet1/3 unassigned YES unset down down

GigabitEthernet1/4 unassigned YES unset down down

GigabitEthernet1/5 unassigned YES unset down down

GigabitEthernet1/6 unassigned YES unset down down

GigabitEthernet1/7 unassigned YES unset down down

GigabitEthernet1/8 unassigned YES unset down down

GigabitEthernet1/9 unassigned YES unset down down

GigabitEthernet1/10 unassigned YES unset down down

GigabitEthernet1/11 unassigned YES unset down down

GigabitEthernet1/12 unassigned YES unset down down

GigabitEthernet1/13 unassigned YES unset down down

GigabitEthernet1/14 unassigned YES unset down down

GigabitEthernet1/15 unassigned YES unset up up

GigabitEthernet1/16 unassigned YES unset down down

GigabitEthernet1/17 unassigned YES unset down down

GigabitEthernet1/18 unassigned YES unset down down

GigabitEthernet1/19 unassigned YES unset down down

GigabitEthernet1/20 unassigned YES unset down down

GigabitEthernet3/1 unassigned YES unset up up

GigabitEthernet3/2 unassigned YES unset up up

GigabitEthernet3/3 unassigned YES unset up up

GigabitEthernet3/4 unassigned YES unset up up

GigabitEthernet3/5 unassigned YES unset up up

GigabitEthernet3/6 unassigned YES unset up up

GigabitEthernet3/7 unassigned YES unset up up

## 小结一下：在刚才的配置过程中，端口Gi1/2下面所连接的电脑的网关就是vlan200的地址——10.10.0.1。下面所连的电脑找到相应的网关后在会去找具体的路由，这些我们下节会讲解。

TEST#show inter trunk

# 显示当前交换机中的trunk接口。作为trunk接口的端口下联的是接入层（或者是汇聚层）的交换机。

Port Mode Encapsulation Status Native vlan

Gi1/15 on 802.1q trunking 1

Gi3/17 on 802.1q trunking 1

Gi3/20 on 802.1q trunking 1

Gi3/21 on 802.1q trunking 1

Gi3/22 on 802.1q trunking 1

Gi3/23 on 802.1q trunking 1

Gi3/24 on 802.1q trunking 1

Port Vlans allowed on trunk

Gi1/15 1-4094

Gi3/17 1-4094

Gi3/20 1-4094

Gi3/21 1-4094

Gi3/22 1-4094

Gi3/23 1-4094

Gi3/24 1-4094

Port Vlans allowed and active in management domain

Gi1/15 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/17 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/20 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/21 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/22 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/23 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/24 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Port Vlans in spanning tree forwarding state and not pruned

Gi1/15 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/17 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/20 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/21 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/22 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/23 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

Gi3/24 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160,200

TEST#conf t

Enter configuration commands, one per line. End with CNTL/Z.

TEST(config)#int gi1/15 # 我们以gi1/15来说明，如何将此端口配置成trunk接口

TEST(config-if)#switchport mode ? # 首先定义此接口的模式为trunk

access Set trunking mode to ACCESS unconditionally

dynamic Set trunking mode to dynamically negotiate access or trunk mode

private-vlan Set the mode to private-vlan host or promiscuous

trunk Set trunking mode to TRUNK unconditionally

TEST(config-if)#switchport mode trunk

TEST(config-if)#switchport trunk encapsulation ?

# 然后定义trunk口的封装类型，此处选择dot1q也叫802.1q，为通用封装类型

dot1q Interface uses only 802.1q trunking encapsulation when trunking

isl Interface uses only ISL trunking encapsulation when trunking

negotiate Device will negotiate trunking encapsulation with peer on interface

TEST(config-if)#switchport trunk encapsulation dot1q

# 回车后就将此trunk口的封装类型定义成了dot1q

## 小结一下：刚才配置的是如何将下联接入层交换机的端口配置成trunk模式，并且如何将此trunk口封装成特定的类型，接下来我们介绍如何配置此核心交换机的VTP的一些相关设置。

TEST(config)#vtp mode ?

client Set the device to client mode.

server Set the device to server mode.

transparent Set the device to transparent mode.

TEST(config)#vtp mode server

# 首先我们在全局配置模式中将vtp的mode设置成server

TEST(config)#vtp domain pjoe

# 然后配置vtp的domain，所有的交换机应该在一个domain中，此例中我们定义的doamin为pjoe

TEST(config)#vtp password pjoeserver

# 配置此vtp的介入密码，这样可以防止未授权的交换机随便加入到这个domian中来。

TEST#sh vtp status # 配置完毕后显示一下vtp的状态

VTP Version : 2

Configuration Revision : 22

Maximum VLANs supported locally : 1005

Number of existing VLANs : 20

VTP Operating Mode : Server # vtp的模式为server模式

VTP Domain Name : pjoe # vtp的域名是pjoe

VTP Pruning Mode : Disabled

VTP V2 Mode : Disabled

VTP Traps Generation : Enabled

MD5 digest : 0x00 0xB3 0x21 0xB7 0x56 0xD7 0x06 0x4F

# 此处表示的是vtp的密码（已加密）

Configuration last modified by 192.168.113.254 at 12-3-07 22:52:46

Local updater ID is 192.168.113.254 on interface Vl1 (lowest numbered VLAN interface found)

TEST#

## 小结一下：经过以上的配置就将核心交换机的vtp等的配置工作完成了，只需要再配置好接入交换机的相关vtp参数和对应的trunk接口，接入交换机就能够从核心交换机上获取到所有的vlan信息，而不需要重新建立各个vlan。

TEST#sh vlan # 接下来我们去掉新增加的vlan，先显示一下。

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Gi1/3, Gi1/4, Gi1/5, Gi1/6, Gi1/7, Gi1/8, Gi1/9, Gi1/10, Gi1/11, Gi1/12, Gi1/14, Gi1/16, Gi1/17, Gi1/18, Gi1/19, Gi1/20, Gi3/12, Gi3/13, Gi3/14,

2 firewall active Gi1/1

10 Engineering active Gi3/9, Gi3/10

20 Procurement active Gi3/19

30 QAQC active

40 Operation active

50 Yard active Gi3/18

60 BM active

70 HRAD active

80 Facility active

100 Finance active

110 GO active

120 Wlan active

150 Server active Gi3/1, Gi3/2, Gi3/3, Gi3/4, Gi3/5, Gi3/6, Gi3/7, Gi3/8

160 Client active Gi3/11, Gi3/15

200 test active Gi1/2

1002 fddi-default act/unsup

1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1 enet 100001 1500 - - - - - 0 0

2 enet 100002 1500 - - - - - 0 0

10 enet 100010 1500 - - - - - 0 0

20 enet 100020 1500 - - - - - 0 0

30 enet 100030 1500 - - - - - 0 0

40 enet 100040 1500 - - - - - 0 0

50 enet 100050 1500 - - - - - 0 0

60 enet 100060 1500 - - - - - 0 0

70 enet 100070 1500 - - - - - 0 0

80 enet 100080 1500 - - - - - 0 0

100 enet 100100 1500 - - - - - 0 0

110 enet 100110 1500 - - - - - 0 0

120 enet 100120 1500 - - - - - 0 0

150 enet 100150 1500 - - - - - 0 0

160 enet 100160 1500 - - - - - 0 0

200 enet 100200 1500 - - - - - 0 0

1002 fddi 101002 1500 - - - - - 0 0

1003 tr 101003 1500 - - - - - 0 0

TEST#conf t

Enter configuration commands, one per line. End with CNTL/Z.

TEST(config)#no vlan 200 # 第一步，删除vlan200

TEST(config)#no int vlan 200 # 第二步，删除int vlan200 ，经过这两步就可以彻底的删除vlan200了

TEST(config)int gi1/2 # 进入到gi1/2这个端口中

TEST(config-if)#switchport access vlan 1 # 将这个端口重新划分到vlan1中

TEST(config-if)#end

TEST#shv vlan

# 确认一下，我们成功的将gi1/2回归到vlan1中，并且删除掉了vlan200

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Gi1/2, Gi1/3, Gi1/4, Gi1/5, Gi1/6, Gi1/7, Gi1/8, Gi1/9, Gi1/10, Gi1/11, Gi1/13, Gi1/14, Gi1/16, Gi1/17, Gi1/18, Gi1/19, Gi1/20, Gi3/12, Gi3/13, Gi3/16

2 firewall active Gi1/1

10 Engineering active Gi3/9, Gi3/10

20 Procurement active Gi3/19

30 QAQC active

40 Operation active

50 Yard active Gi3/18

60 BM active

70 HRAD active

80 Facility active

100 Finance active

110 GO active

120 Wlan active

150 Server active Gi3/1, Gi3/2, Gi3/3, Gi3/4, Gi3/5, Gi3/6, Gi3/7, Gi3/8

160 Client active Gi3/11, Gi3/15

1002 fddi-default act/unsup

1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1 enet 100001 1500 - - - - - 0 0

2 enet 100002 1500 - - - - - 0 0

10 enet 100010 1500 - - - - - 0 0

20 enet 100020 1500 - - - - - 0 0

30 enet 100030 1500 - - - - - 0 0

40 enet 100040 1500 - - - - - 0 0

50 enet 100050 1500 - - - - - 0 0

60 enet 100060 1500 - - - - - 0 0

70 enet 100070 1500 - - - - - 0 0

80 enet 100080 1500 - - - - - 0 0

100 enet 100100 1500 - - - - - 0 0

110 enet 100110 1500 - - - - - 0 0

120 enet 100120 1500 - - - - - 0 0

150 enet 100150 1500 - - - - - 0 0

160 enet 100160 1500 - - - - - 0 0

1002 fddi 101002 1500 - - - - - 0 0

1003 tr 101003 1500 - - - - - 0 0

1004 fdnet 101004 1500 - - - ieee - 0 0

以上是关于H3C和CISCO交换机做聚合配置实例教学的主要内容，如果未能解决你的问题，请参考以下文章

cisco+H3C交换机SSH配置实例

Cisco交换机VLAN与TRUNK链路配置命令

手工配置链路聚合ensp报错

h3c端口聚合命令

2019-05-17 LACP 链路聚合以及配置实例

h3c端口聚合命令