ZYNQ之FPGA学习----IIC协议驱动模块仿真实验

Posted 鲁棒最小二乘支持向量机

tags:

篇首语:本文由小常识网(cha138.com)小编为大家整理,主要介绍了ZYNQ之FPGA学习----IIC协议驱动模块仿真实验相关的知识,希望对你有一定的参考价值。

1 IIC通信协议简介

IIC通信协议基础知识学习:硬件设计基础----通信协议IIC

2 实验任务

设计IIC驱动模块,并进行仿真验证,观察仿真波形

3 实验设计

3.1 创建工程

新建工程,操作如图所示:

输入工程名和路径,如图:

选择创建RTL工程,如图:

直接点击Next:

继续点击Next:

添加芯片型号,操作如图:

工程创建完成:

3.2 设计输入

创建工程文件,操作如图所示:

创建iic_drive文件:

创建完成:

双击打开,输入代码如下:

module iic_drive(
//系统接口
    input               clk,      //时钟信号,50MHZ
    input               rst_n,    //复位信号,低电平有效
 //IIC时序控制接口                   
    input                i2c_exec   ,  //IIC触发执行信号
    input                bit_ctrl   ,  //字地址位控制(16b/8b)
    input                i2c_rh_wl  ,  //IIC读写控制信号
    input        [15:0]  i2c_addr   ,  //IIC器件内地址
    input        [ 7:0]  i2c_data_w ,  //IIC要写的数据
    output  reg  [ 7:0]  i2c_data_r ,  //IIC读出的数据
    output  reg          i2c_done   ,  //IIC一次操作完成
    output  reg          i2c_ack    ,  //IIC应答标志 0:应答 1:未应答
//IIC物理接口
    output  reg          scl        ,  //IIC的SCL时钟信号
    inout                sda        ,  //IIC的SDA信号                                 
    //user interface                   
    output  reg          dri_clk       //驱动IIC操作的驱动时钟
    );
parameter   SLAVE_ADDR = 7'b1010000   ;  //IIC从机地址    
parameter   CLK_FREQ   = 26'd50_000_000; //模块输入的时钟频率
parameter   I2C_FREQ   = 18'd250_000;     //IIC_SCL的时钟频率 ,250k   
//状态机定义
localparam  st_idle     = 8'b0000_0001; //空闲状态
localparam  st_sladdr   = 8'b0000_0010; //发送器件地址(slave address)
localparam  st_addr16   = 8'b0000_0100; //发送16位字地址
localparam  st_addr8    = 8'b0000_1000; //发送8位字地址
localparam  st_data_wr  = 8'b0001_0000; //写数据(8 bit)
localparam  st_addr_rd  = 8'b0010_0000; //发送器件地址读
localparam  st_data_rd  = 8'b0100_0000; //读数据(8 bit)
localparam  st_stop     = 8'b1000_0000; //结束IIC操作
//reg 定义
reg            sda_dir   ; //IIC数据(SDA)方向控制
reg            sda_out   ; //SDA输出信号
reg            st_done   ; //状态结束
reg            wr_flag   ; //写标志
reg    [ 6:0]  cnt       ; //计数
reg    [ 7:0]  cur_state ; //状态机当前状态
reg    [ 7:0]  next_state; //状态机下一状态
reg    [15:0]  addr_t    ; //地址
reg    [ 7:0]  data_r    ; //读取的数据
reg    [ 7:0]  data_wr_t ; //IIC需写的数据的临时寄存
reg    [ 9:0]  clk_cnt   ; //分频时钟计数

//wire 定义
wire          sda_in     ; //SDA输入信号
wire   [8:0]  clk_divide ; //模块驱动时钟的分频系数
//SDA控制
assign  sda        = sda_dir ?  sda_out : 1'bz   ;  //SDA数据输出或高阻
assign  sda_in     = sda                         ;  //SDA数据输入
assign  clk_divide = (CLK_FREQ/I2C_FREQ) >> 2'd2 ;  //模块驱动时钟的分频系数

//生成IIC的SCL的四倍频率的驱动时钟用于驱动IIC的操作
always @(posedge clk or negedge rst_n) begin
    if(!rst_n) begin
        dri_clk <=  1'b0;
        clk_cnt <= 10'd0;
    end
    else if(clk_cnt == clk_divide[8:1] - 1'd1) begin
        clk_cnt <= 10'd0;
        dri_clk <= ~dri_clk;
    end
    else
        clk_cnt <= clk_cnt + 1'b1;
end

//(三段式状态机)同步时序描述状态转移
always @(posedge dri_clk or negedge rst_n) begin
    if(!rst_n)
        cur_state <= st_idle;
    else
        cur_state <= next_state;
end

//组合逻辑判断状态转移条件
always @(*) begin
    next_state = st_idle;
    case(cur_state)
        st_idle: begin                          //空闲状态
           if(i2c_exec) begin
               next_state = st_sladdr;
           end
           else
               next_state = st_idle;
        end
        st_sladdr: begin
            if(st_done) begin
                if(bit_ctrl)                    //判断是16位还是8位字地址
                   next_state = st_addr16;
                else
                   next_state = st_addr8 ;
            end
            else
                next_state = st_sladdr;
        end
        st_addr16: begin                        //写16位字地址
            if(st_done) begin
                next_state = st_addr8;
            end
            else begin
                next_state = st_addr16;
            end
        end
        st_addr8: begin                         //8位字地址
            if(st_done) begin
                if(wr_flag==1'b0)               //读写判断
                    next_state = st_data_wr;
                else
                    next_state = st_addr_rd;
            end
            else begin
                next_state = st_addr8;
            end
        end
        st_data_wr: begin                       //写数据(8 bit)
            if(st_done)
                next_state = st_stop;
            else
                next_state = st_data_wr;
        end
        st_addr_rd: begin                       //写地址以进行读数据
            if(st_done) begin
                next_state = st_data_rd;
            end
            else begin
                next_state = st_addr_rd;
            end
        end
        st_data_rd: begin                       //读取数据(8 bit)
            if(st_done)
                next_state = st_stop;
            else
                next_state = st_data_rd;
        end
        st_stop: begin                          //结束I2C操作
            if(st_done)
                next_state = st_idle;
            else
                next_state = st_stop ;
        end
        default: next_state= st_idle;
    endcase
end

//时序电路描述状态输出
always @(posedge dri_clk or negedge rst_n) begin
    //复位初始化
    if(!rst_n) begin
        scl       <= 1'b1;
        sda_out   <= 1'b1;
        sda_dir   <= 1'b1;                          
        i2c_done  <= 1'b0;                          
        i2c_ack   <= 1'b0;                          
        cnt       <= 1'b0;                          
        st_done   <= 1'b0;                          
        data_r    <= 1'b0;                          
        i2c_data_r<= 1'b0;                          
        wr_flag   <= 1'b0;                          
        addr_t    <= 1'b0;                          
        data_wr_t <= 1'b0;                          
    end                                              
    else begin                                       
        st_done <= 1'b0 ;                            
        cnt     <= cnt +1'b1 ;                       
        case(cur_state)                              
             st_idle: begin                          //空闲状态
                scl     <= 1'b1;                     
                sda_out <= 1'b1;                     
                sda_dir <= 1'b1;                     
                i2c_done<= 1'b0;                     
                cnt     <= 7'b0;               
                if(i2c_exec) begin                   
                    wr_flag   <= i2c_rh_wl ;         
                    addr_t    <= i2c_addr  ;         
                    data_wr_t <= i2c_data_w;  
                    i2c_ack   <= 1'b0;                      
                end                                  
            end                                      
            st_sladdr: begin                         //写地址(器件地址和字地址)
                case(cnt)                            
                    7'd1 : sda_out <= 1'b0;          //开始IIC
                    7'd3 : scl <= 1'b0;              
                    7'd4 : sda_out <= SLAVE_ADDR[6]; //传送器件地址
                    7'd5 : scl <= 1'b1;              
                    7'd7 : scl <= 1'b0;              
                    7'd8 : sda_out <= SLAVE_ADDR[5]; 
                    7'd9 : scl <= 1'b1;              
                    7'd11: scl <= 1'b0;              
                    7'd12: sda_out <= SLAVE_ADDR[4]; 
                    7'd13: scl <= 1'b1;              
                    7'd15: scl <= 1'b0;              
                    7'd16: sda_out <= SLAVE_ADDR[3]; 
                    7'd17: scl <= 1'b1;              
                    7'd19: scl <= 1'b0;              
                    7'd20: sda_out <= SLAVE_ADDR[2]; 
                    7'd21: scl <= 1'b1;              
                    7'd23: scl <= 1'b0;              
                    7'd24: sda_out <= SLAVE_ADDR[1]; 
                    7'd25: scl <= 1'b1;              
                    7'd27: scl <= 1'b0;              
                    7'd28: sda_out <= SLAVE_ADDR[0]; 
                    7'd29: scl <= 1'b1;              
                    7'd31: scl <= 1'b0;              
                    7'd32: sda_out <= 1'b0;          //0:写
                    7'd33: scl <= 1'b1;              
                    7'd35: scl <= 1'b0;              
                    7'd36: begin                     
                        sda_dir <= 1'b0;             
                        sda_out <= 1'b1;                         
                    end                              
                    7'd37: scl     <= 1'b1;            
                    7'd38: begin                     //从机应答 
                        st_done <= 1'b1;
                        if(sda_in == 1'b1)           //高电平表示未应答
                            i2c_ack <= 1'b1;         //拉高应答标志位     
                    end                                          
                    7'd39: begin                     
                        scl <= 1'b0;                 
                        cnt <= 1'b0;                 
                    end                              
                    default :  ;                     
                endcase                              
            end                                      
            st_addr16: begin                         
                case(cnt)                            
                    7'd0 : begin                     
                        sda_dir <= 1'b1 ;            
                        sda_out <= addr_t[15];       //传送字地址
                    end                              
                    7'd1 : scl <= 1'b1;              
                    7'd3 : scl <= 1'b0;              
                    7'd4 : sda_out <= addr_t[14];    
                    7'd5 : scl <= 1'b1;              
                    7'd7 : scl <= 1'b0;              
                    7'd8 : sda_out <= addr_t[13];    
                    7'd9 : scl <= 1'b1;              
                    7'd11: scl <= 1'b0;              
                    7'd12: sda_out <= addr_t[12];    
                    7'd13: scl <= 1'b1;              
                    7'd15: scl <= 1'b0;              
                    7'd16: sda_out <= addr_t[11];    
                    7'd17: scl <= 1'b1;              
                    7'd19: scl <= 1'b0;              
                    7'd20: sda_out <= addr_t[10];    
                    7'd21: scl <= 1'b1;              
                    7'd23: scl <= 1'b0;              
                    7'd24: sda_out <= addr_t[9];     
                    7'd25: scl <= 1'b1;              
                    7'd27: scl <= 1'b0;              
                    7'd28: sda_out <= addr_t[8];     
                    7'd29: scl <= 1'b1;              
                    7'd31: scl <= 1'b0;              
                    7'd32: begin                     
                        sda_dir <= 1'b0;             
                        sda_out <= 1'b1;   
                    end                              
                    7'd33: scl  <= 1'b1;             
                    7'd34: begin                     //从机应答
                        st_done <= 1'b1;     
                        if(sda_in == 1'b1)           //高电平表示未应答
                            i2c_ack <= 1'b1;         //拉高应答标志位    
                    end        
                    7'd35: begin                     
                        scl <= 1'b0;                 
                        cnt <= 1'b0;                 
                    end                              
                    default :  ;                     
                endcase                              
            end                                      
            st_addr8: begin                          
                case(cnt)                            
                    7'd0: begin                      
                       sda_dir <= 1'b1 ;             
                       sda_out <= addr_t[7];         //字地址
                    end                              
                    7'd1 : scl <= 1'b1;              
                    7'd3 : scl <= 1'b0;              
                    7'd4 : sda_out <= addr_t[6];     
                    7'd5 : scl <= 1'b1;              
                    7'd7 : scl <= 1'b0;              
                    7'd8 : sda_out <= addr_t[5];     
                    7'd9 : scl <= 1'b1;              
                    7'd11: scl <= 1'b0;              
                    7'd12: sda_out <= addr_t[4];     
                    7'd13: scl <= 1'b1;              
                    7'd15: scl <= 1'b0;              
                    7'd16: sda_out <= addr_t[3];     
                    7'd17: scl <= 1'b1;              
                    7'd19: scl <= 1'b0;              
                    7'd20: sda_out <= addr_t[2];     
                    7'd21: scl <= 1'b1;              
                    7'd23: scl <= 1'b0;              
                    7'd24: sda_out <= addr_t[1];     
                    7'd25: scl <= 1'b1;              
                    7'd27: scl <= 1'b0;              
                    7'd28: sda_out <= addr_t[0];     
                    7'd29: scl <= 1'b1;              
                    7'd31: scl <= 1'b0;              
                    7'd32: begin                     
                        sda_dir <= 1'b0;         
                        sda_out <= 1'b1;                    
                    end                              
                    7'd33: scl     <= 1'b1;          
                    7'd34: begin                     //从机应答
                        st_done <= 1'b1;     
                        if(sda_in == 1'b1)           //高电平表示未应答
                            i2c_ack <= 1'b1;         //拉高应答标志位    
                    end   
                    7'd35: begin                     
                        scl <= 1'b0;                 
                        cnt <= 1'b0;                 
                    end                              
                    default :  ;                     
                endcase                              
            end                                      
            st_data_wr: begin                        //写数据(8 bit)
                case(cnt)                            
                    7'd0: begin                      
                        sda_out <= data_wr_t[7];     //IIC写8位数据
                        sda_dir <= 1'b1;             
                    end                              
                    7'd1 : scl <= 1'b1;              
                    7'd3 : scl <= 1'b0;              
                    7'd4 : sda_out <= data_wr_t[6];  
                    7'd5 : scl <= 1'b1;              
                    7'd7 : scl <= 1'b0;              
                    7'd8 : sda_out <= data_wr_t[5];  
                    7'd9 : scl <= 1'b1;              
                    7'd11: scl <= 1'b0;              
                    7'd12: sda_out <= data_wr_t[4];  
                    7'd13: scl <= 1'b1;              
                    7'd15: scl <= 1'b0;              
                    7'd16: sda_out <= data_wr_t[3];  
                    7'd17: scl <= 1'b1;              
                    7'd19: scl <= 1'b0;              
                    7'd20: sda_out <= data_wr_t[2];  
                    7'd21: scl <= 1'b1;              
                    7'd23: scl <= 1'b0;              
                    7'd24: sda_out <= data_wr_t[1];  
                    7'd25: scl <= 1'b1;              
                    7'd27: scl <= 1'b0;              
                    7'd28: sda_out <= data_wr_t[0];  
                    7'd29: scl <= 1'b1;              
                    7'd31: scl <= 1'b0;              
                    7'd32: begin                     
                        sda_dir <= 1'b0;           
                        sda_out <= 1'b1;                              
                    end                              
                    7'd33: scl <= 1'b1;              
                    7'd34: begin                     //从机应答
                        st_done <= 1'b1;     
                        if(sda_in == 1'b1)           //高电平表示未应答
                            i2c_ack <= 1'b1;         //拉高应答标志位    
                    end          
                    7'd35: begin                     
                        scl  <= 1'b0;                
                        cnt  <= 1'b0;                
                    end                              
                    default  :  ;                    
                endcase                              
            end                                      
            st_addr_rd: begin                        //写地址以进行读数据
                case(cnt)                            
                    7'd0 : begin                     
                        sda_dir <= 1'b1;             
                        sda_out <= 1'b1;             
                    end                              
                    7'd1 : scl <= 1'b1;              
                    7'd2 : sda_out <= 1'b0;          //重新开始
                    7'd3 : scl <= 1'b0;              
                    7'd4 : sda_out <= SLAVE_ADDR[6]; //传送器件地址
                    7'd5 : scl <= 1'b1;              
                    7'd7 : scl <= 1'b0;              
                    7'd8 : sda_out <= SLAVE_ADDR[5]; 
                    7'd9 : scl <= 1'b1;              
                    7'd11: scl <= 1'b0;              
                    7'd12: sda_out <= SLAVE_ADDR[4]; 
                    7'd13: scl <= 1'b1;              
                    7'd15: scl <= 1'b0;              
                    7'd16: sda_out <= SLAVE_ADDR[3]; 
                    7'd17: scl <= 1'b1;              
                    7'd19: scl <= 1'b0;              
                    7'd20: sda_out <= SLAVE_ADDR[2]; 
                    7'd21: scl <= 1'b1;              
                    7'd23: scl <= 1'b0;              
                    7'd24: sda_out <= SLAVE_ADDR[1]; 
                    7'd25: scl <= 1'b1;              
                    7ZYNQ之FPGA学习----EEPROM读写测试实验

一视频处理FPGA驱动OV7725摄像头模块

ZYNQ之FPGA学习----UART串口实验

ZYNQ之FPGA学习----RAM IP核使用实验

ZYNQ之FPGA学习----Vivado功能仿真

SylixOS下基于Zynq-7000加载FPGA程序