3Par7200存储低电压告警
Posted
tags:
篇首语：本文由小常识网(cha138.com)小编为大家整理，主要介绍了3Par7200存储低电压告警相关的知识，希望对你有一定的参考价值。
ss7200 cli% cgcmd -tc tty -C cage0 -c report_faults -p a ##查看报错电源
----------------------------------------------------------------------
Drive Manager faults
No faults
Environmental Control faults
No faults
General Service faults
9 component(s) registered with fault tracker
Local faults:
No faults
Remote faults:
No faults
Human Interface Device faults
Ops Panel status:
Unit Identifier LED : OFF
Logic Fault LED : OFF
Module Fault LED : ON
Warning: Local: Remote:
****No HID warnings to report****
Reporting Current Alarms(Highest priority first):
Type : PCM Failure - redundant
Current State : MUTE
Status : ACTIVE
Buzzer : MUTE
RemoteSync Client faults
No faults
----------------------------------------------------------------------
----------------------------------------------------------------------
Power Manager faults
PSU 0 fault: "DC under Voltage" Fault LED: OFF, Warning LED: OFF, Shutdown LED: OFF
##报警电源编号PSU 0
----------------------------------------------------------------------
ss7200 cli% cgcmd -tc tty -C cage0 -c report_faults -p a ##更换电源后重新查看设备错误
----------------------------------------------------------------------
Drive Manager faults
No faults
Environmental Control faults
No faults
General Service faults
9 component(s) registered with fault tracker
Local faults:
No faults
Remote faults:
No faults
Human Interface Device faults
Ops Panel status:
Unit Identifier LED : OFF
Logic Fault LED : OFF
Module Fault LED : OFF
Warning: Local: Remote:
****No HID warnings to report****
No alarms to report
RemoteSync Client faults
No faults
Power Manager faults
No faults
----------------------------------------------------------------------
ss7200 cli% exit ##无错误，退出系统
补充知识3par7200
ss7200 cli% help ##查看命令帮助
help/clihelp - Help for the HP specific CLI commands.
See the tclsh and Tcl documentation for help on the Tcl language.
CLI commands fall under the following categories:
add - add resources
admit - admit resources
cancel - cancel operations
change - change current domain cli environment
check - check volumes or logical disks for consistency
cmore - page command output
compact - consolidate space
control - control physical entities (disks, ports, magazines)
create - create new entities such as volumes
dismiss - remove entities from system use
exit - exit from this shell (same as quit)
free - free resources
grow - grow entities such as volumes
hist - display service time histograms
locate - identify physical system resources
move - move data from one resource to another
promote - promote a copy to a base volume
quit - exit from this shell (same as exit)
remove - remove entities such as volumes
service - prepare system to begin or complete service
set - set specific parameters
show - display information about resources
shutdown - shutdown a single node or the entire system
sr - historical reports from system reporter
start - start entities (Remote Copy groups, volumes, logical disks)
stat - display statistics for performance resources
stop - stop entities (Remote Copy groups, etc.)
sync - synchronize Remote Copy volume groups
tune - tune resources
update - update objects
upgrade - upgrade firmware of system components
wait - wait for operations to complete
help usage:
help This help message. List command categories.
help <command> Help on specific <command>
help <category> Help on specific <category> of commands
help sub List subjects other than commands
help -sub <subject> Help on <subject>. Same as "help sub,<subject>"
help -col <command> Explain column headers for <command>
Same as "help col,<command>"
help -search <regex> Search help text with regular expression <regex>
"clihelp" can be used instead of "help"
Help on a specific <command> can also be obtained by typing "<command> -h"
(C) Copyright 2002-2013 Hewlett-Packard Development Company, L.P.
ss7200 cli% help show ##查看常用命令帮助
show* - Show information about resources.
In each case type "help <command>" for detailed help.
showalert - show status of system alerts
showaocfg - show all Adaptive Optimization configurations
showauthparam - show authentication parameters
showbattery - show battery status information
showblock - show block mapping info for vvs, lds, pds
showcage - show disk cage information
showcert - show SSL certificate
showcim - show the CIM server information
showclienv - show CLI environment parameters
showcpg - show Common Provisioning Groups (CPGs)
showdate - show date and time on all system nodes
showdomain - show domains in the system
showdomainset - show sets of domains in the system
showeeprom - show node eeprom information
showencryption - show encryption information
showeventlog - show event logs
showfirmwaredb - show current database of firmware levels
showhost - show host and host path information
showhostset - show sets of hosts in the system
showinventory - show hardware inventory
showiscsisession - show iscsi sessions
showld - show logical disks (LDs) in the system
showldch - show LD to PD chunklet mapping
showldmap - show LD to VV mapping
showlicense - show installed license key
shownet - show network configuration and status
shownode - show node and its component information
shownodeenv - show node environmental status (voltages,
temperatures)
showpatch - show what patches have been applied to the system
showpd - show physical disks (PDs) in the system
showpdata - show preserved data status
showpdch - show status of selected chunklets of physical disks
showpdvv - show PD to VV mapping
showport - show Fibre Channel and iSCSI ports in the system
showportarp - show ARP table for ports
showportdev - show detailed information about devices on a port
showportisns - show iSNS host information for ports
showportlesb - show Link Error Status Block information about
devices on Fibre Channel port
showportpel - show Phy Error Log information about
devices on SAS port
showqos - show QoS rules in the system
showrcopy - show Remote Copy configuration information
showrctransport - show information about end-to-end transport for
Remote Copy
showrole - show information about roles in the system
showrsv - show information about reservation and registration
of VLUNs connected on a Fibre Channel port
showsched - show scheduled tasks in the system
showsnmppw - shows SNMP access passwords
showsnmpmgr - show SNMP trap managers
showsnmpuser - show SNMPv3 users and their authentication and privacy protocols
showspace - show estimated free space
showspare - show information about spare and relocated chunklets
showsralertcrit - show System Reporter alert criteria
showsshkey - show ssh public keys authorized by the current user
showsys - show system information (system name, serial number etc.)
showsysmgr - show system manager startup state
showtarget - show unrecognized targets
showtask - show information about tasks
showtemplate - show templates
showtoc - show system Table of Contents (TOC) summary
showtocgen - show system Table of Contents (TOC) generation number
showuser - show user accounts and SSH keys
showuseracl - show user access control list
showuserconn - show user connections
showversion - show software versions
showvlun - show virtual LUNs (VLUNs) in the system
showvv - show virtual volumes (VVs) in the system
showvvcpg - show VV space distribution among CPGs
showvvmap - show VV to LD mapping
showvvpd - show VV distribution across PDs
showvvset - show sets of VVs in the system
showwsapi - show the Web Services API server information
showwsapisession - show the Web Services API server sessions information
Use setclienv command to change the table format options.
以上是关于3Par7200存储低电压告警的主要内容，如果未能解决你的问题，请参考以下文章