用c语言编写modbus程序

Posted 2023-05-04

参考技术A #ifdef MODBUS
//
//******************************************************************************
// CRC 16 Data Table
// *****************
const unsigned int crc_tbl[256]=
0x0000, 0xC0C1, 0xC181, 0x0140, 0xC301, 0x03C0, 0x0280, 0xC241,
0xC601, 0x06C0, 0x0780, 0xC741, 0x0500, 0xC5C1, 0xC481, 0x0440,
0xCC01, 0x0CC0, 0x0D80, 0xCD41, 0x0F00, 0xCFC1, 0xCE81, 0x0E40,
0x0A00, 0xCAC1, 0xCB81, 0x0B40, 0xC901, 0x09C0, 0x0880, 0xC841,
0xD801, 0x18C0, 0x1980, 0xD941, 0x1B00, 0xDBC1, 0xDA81, 0x1A40,
0x1E00, 0xDEC1, 0xDF81, 0x1F40, 0xDD01, 0x1DC0, 0x1C80, 0xDC41,
0x1400, 0xD4C1, 0xD581, 0x1540, 0xD701, 0x17C0, 0x1680, 0xD641,
0xD201, 0x12C0, 0x1380, 0xD341, 0x1100, 0xD1C1, 0xD081, 0x1040,
0xF001, 0x30C0, 0x3180, 0xF141, 0x3300, 0xF3C1, 0xF281, 0x3240,
0x3600, 0xF6C1, 0xF781, 0x3740, 0xF501, 0x35C0, 0x3480, 0xF441,
0x3C00, 0xFCC1, 0xFD81, 0x3D40, 0xFF01, 0x3FC0, 0x3E80, 0xFE41,
0xFA01, 0x3AC0, 0x3B80, 0xFB41, 0x3900, 0xF9C1, 0xF881, 0x3840,
0x2800, 0xE8C1, 0xE981, 0x2940, 0xEB01, 0x2BC0, 0x2A80, 0xEA41,
0xEE01, 0x2EC0, 0x2F80, 0xEF41, 0x2D00, 0xEDC1, 0xEC81, 0x2C40,
0xE401, 0x24C0, 0x2580, 0xE541, 0x2700, 0xE7C1, 0xE681, 0x2640,
0x2200, 0xE2C1, 0xE381, 0x2340, 0xE101, 0x21C0, 0x2080, 0xE041,
0xA001, 0x60C0, 0x6180, 0xA141, 0x6300, 0xA3C1, 0xA281, 0x6240,
0x6600, 0xA6C1, 0xA781, 0x6740, 0xA501, 0x65C0, 0x6480, 0xA441,
0x6C00, 0xACC1, 0xAD81, 0x6D40, 0xAF01, 0x6FC0, 0x6E80, 0xAE41,
0xAA01, 0x6AC0, 0x6B80, 0xAB41, 0x6900, 0xA9C1, 0xA881, 0x6840,
0x7800, 0xB8C1, 0xb981, 0x7940, 0xBB01, 0x7BC0, 0x7A80, 0xBA41,
0xBE01, 0x7EC0, 0x7F80, 0xBF41, 0x7D00, 0xBDC1, 0xBC81, 0x7C40,
0xB401, 0x74C0, 0x7580, 0xB541, 0x7700, 0xB7C1, 0xB681, 0x7640,
0x7200, 0xB2C1, 0xB381, 0x7340, 0xB101, 0x71C0, 0x7080, 0xB041,
0x5000, 0x90C1, 0x9181, 0x5140, 0x9301, 0x53C0, 0x5280, 0x9241,
0x9601, 0x56C0, 0x5780, 0x9741, 0x5500, 0x95C1, 0x9481, 0x5440,
0x9C01, 0x5CC0, 0x5D80, 0x9D41, 0x5F00, 0x9FC1, 0x9E81, 0x5E40,
0x5A00, 0x9AC1, 0x9B81, 0x5B40, 0x9901, 0x59C0, 0x5880, 0x9841,
0x8801, 0x48C0, 0x4980, 0x8941, 0x4B00, 0x8BC1, 0x8A81, 0x4A40,
0x4E00, 0x8EC1, 0x8F81, 0x4F40, 0x8D01, 0x4DC0, 0x4C80, 0x8C41,
0x4400, 0x84C1, 0x8581, 0x4540, 0x8701, 0x47C0, 0x4680, 0x8641,
0x8201, 0x42C0, 0x4380, 0x8341, 0x4100, 0x81C1, 0x8081, 0x4040;
//#pragma end_abs_address
//******************************************************************************
//

#define DEFAULT_ADDRESS 1 // all slaves start with this Modbus address
// communication commands:
//#define CHOOSE_SLOT 0x80
//#define POLL_SLOT 0x81
//#define POLL_ACK 0x82

// positions in a Modbus packet
#define ADDR 0
#define FCN 1
#define REGHI 2
#define REGLO 3
#define NUMREGSHI 4
#define NUMREGSLO 5
#define OUTBYTES 2

// Modbus exception codes
#define FCN_NOT_SUPPORTED 1 // a Modbus function code we can't
handle
#define BAD_ADDR_OR_CMD 2 // a Modbus "register"
(command or address to us) we don't know
#define BAD_COUNT 3 // num regs != num bytes
* 2
#define CMD_NOT_COMPLETE 4 // command didn't complete
successfully

// other defines
#define IN 0
#define OUT 1
//
// SLOT_NUMBER is the 2 byte device configuration
// the first byte is the ID
// the second byte is the transmission mode coded as follows:
// bit 0x01: 0=19200, 1=9600 baud
// bit 0x02: 0=even parity, 1=odd parity
// bit 0x04: 0=parity, 1=no parity
// bit 0x08: 0=1 stop bit, 1=2 stop bits
// if bit 0x04 is set and bit 0x08 is not set then it's 8
bit mode (vs 9 bit mode)
//
//unsigned char receiveBuffer[32] = 0; // Reserve 32 bytes for packet.
unsigned char device_addr = DEFAULT_ADDRESS; // assigned device address - start
with disconnected
//unsigned char timeout_counter = 10;
//unsigned char timeout_duration = 10; // seconds, default
//unsigned char pkt_index = 0;

// return number of bytes in packet, not including crc
unsigned char MDB_get_length(unsigned char in_out, unsigned char* ptr)

if(comControlByte & 0x20)
return 6;
switch(*(ptr+FCN))

case 0x06: // write single reg
return 6;
case 0x03: // read multiple regs
if (in_out == IN) // incoming packet
return 6;
else
return *(ptr+OUTBYTES) + 3;
case 0x10: // write multiple regs
return (*(ptr+NUMREGSLO) << 1) + 7;
default: // assume error packet
return 3;



// calculate CRC16 on a packet
unsigned int MDB_crc_calc(unsigned char in_out, unsigned char* ptr)

unsigned char c1, c2;
unsigned int crc = 0xffff;
// initial value
unsigned char* ptr_pkt_hdr = ptr;
c2 = MDB_get_length(in_out,ptr);
for(c1=0; c1<c2; c1++)
crc = ((crc >> 8) & 0xFF) ^ crc_tbl[(crc ^ *ptr_pkt_hdr++) & 0xFF];
return crc;


// check crc on an incoming packet
unsigned char MDB_crc_check(unsigned char* ptr)

unsigned int i1;
unsigned char c1, c2, c3;
i1 = MDB_crc_calc(IN, ptr);
c1 = *(ptr+MDB_get_length(IN,ptr)+1); // msb of incoming crc
c2 = *(ptr+MDB_get_length(IN,ptr)); // lsb of
incoming crc
c3 = (i1 >> 8);
// msb of calculated crc
if((c2 == (i1 & 0x00FF)) && (c1 == c3)) // compare msb
& lsb
return 1;
else
return 0;


// send Modbus packets
void MDB_pkt_sender(unsigned char* ptr)

unsigned char idx, pkt_len;
unsigned int i1;
// append crc, lsb 1st
i1 = MDB_crc_calc(OUT,ptr);
pkt_len = MDB_get_length(OUT,ptr);
*(ptr+pkt_len++) = (unsigned char)i1; // lsb
*(ptr+pkt_len++) = (i1 >> 8); // msb
//SCI1C2 = 0x08; // transmit enable
//comLedOn();
PTGD |= 0x80;
for (idx = 0; idx < pkt_len; idx++)

while(!(SCI1S1 & 0x80)); // wait for tdre=1
i1 = SCI1S1;
SCI1D = *(ptr+idx);

while(!(SCI1S1 & 0x80));
while(!(SCI1S1 & 0x40));
//comLedOff();
PTGD &= 0x7f;
//SCI1C2 = 0x2c; // back to receive mode


// return a Modbus error packet
void MDB_error(unsigned char exp_code, unsigned char* ptr)

*(ptr+FCN) |= 0x80; // set error code
*(ptr+FCN+1) = exp_code; // set exception code
MDB_pkt_sender(ptr);


//
void MDB_read_data(unsigned char* ptr)

if(get_data((ptr+2), *(ptr+3)))

// get_data() sticks the length of the data in
receiveBuffer[2]
// receiveBuffer[3] & on will have actual data
// receiveBuffer[0] & receiveBuffer[1] unchanged
MDB_pkt_sender(ptr); // appends CRC before sending

else
MDB_error(BAD_ADDR_OR_CMD, ptr);

// handle data writes
void MDB_write_data(unsigned char* ptr)

if((*(ptr+5)<<1) == *(ptr+6))

switch(*(ptr+3))//receiveBuffer[3])

//case 0x18: // new timeout value
// timeout_duration = receiveBuffer[7];
// MDB_pkt_sender(); // echo
received command
// break;
//case 0x63: // lamp test
// clampTest = 40;
// MDB_pkt_sender(); // echo
received command
// break;
case ADDRESS:
//if(receiveBuffer[8] &&
(receiveBuffer[8] < 248)) // valid addresses
if(*(ptr+8) && (*(ptr+8) < 248))

//device_addr = *
(ptr+8); // not until reset
nonvolatile[0] = *(ptr+8);
// device ID
nonvolatile[1] = *(ptr+7);
// transmission mode
nonvolatile[2] =
~nonvolatile[0];
nonvolatile[3] =
~nonvolatile[1];
writeToNonvolatile
(SLOT_NUMBER, &nonvolatile[0]);
comControlByte |= 0x20;
MDB_pkt_sender(ptr);
comControlByte &= 0xdf;

else
MDB_error
(BAD_ADDR_OR_CMD, ptr);
break;
case INSTALLATION_DATE: // installation
date
readFromNonvolatile(DATE_DATA,
&nonvolatile[0]);
nonvolatile[4] = *
(ptr+7);//receiveBuffer[7];
nonvolatile[5] = *
(ptr+8);//receiveBuffer[8];
nonvolatile[6] = *
(ptr+9);//receiveBuffer[9];
nonvolatile[7] = *
(ptr+10);//receiveBuffer[10];
nonvolatile[12] = ~nonvolatile[4];
nonvolatile[13] = ~nonvolatile[5];
nonvolatile[14] = ~nonvolatile[6];
nonvolatile[15] = ~nonvolatile[7];
writeToNonvolatile(DATE_DATA,
&nonvolatile[0]);
comControlByte |= 0x20;
MDB_pkt_sender(ptr); // echo
received command
comControlByte &= 0xdf;
break;
default:
MDB_error(BAD_ADDR_OR_CMD, ptr);
break;


else
MDB_error(BAD_COUNT, ptr);

//
void MDB_parse(char *bufPtr)

unsigned char i = 0;

if(MDB_crc_check(bufPtr))

if(*(bufPtr+ADDR) == device_addr)

switch(*(bufPtr+FCN))

case 0x03: // modbus read multiple
regs
MDB_read_data(bufPtr);
break;
case 0x10: // modbus write multiple
regs
MDB_write_data(bufPtr);
break;
default: // modbus function not
supported
MDB_error
(FCN_NOT_SUPPORTED, bufPtr);
break;

用C语言编写一个密码验证程序

//用户信息数据结构
typedef struct

long number; //用户编号 6位
char name[20]; //用户名
char password[8]; //用户密码
int power; //权限判断 1 为管理员2为普通用户
user;
user yh[100]=100000,"gavin","gavine",1,100001,"wnag","wangf",2;
密码验证后，让这个结构体里的gavin为管理员，及返回值为1，wang为普通用户，即反值为2；

参考技术A #include <stdio.h>
#include <string.h>

typedef struct

long number; //用户编号 6位
char name[20]; //用户名
char password[8]; //用户密码
int power; //权限判断 1 为管理员2为普通用户
user;
user yh[100]=100000,"gavin","gavine",1,100001,"wnag","wangf",2;
int length = 2;

int checkuser(long num, const char *nm, const char *pwd)

int i;
for (i = 0; i < length; ++i)

if (yh[i].number == num && !strcmp(yh[i].name, nm) && !strcmp(yh[i].password, pwd))

if (1==yh[i].power)
return 1;
else
return 2;




void main()

printf("%d\n", checkuser(100000, "gavin", "gavine"));
本回答被提问者采纳