《DSP using MATLAB》示例Example 8.29

Posted 2020-09-12 沧海一粟

%% ------------------------------------------------------------------------
%%            Output Info about this m-file
fprintf(\'\\n***********************************************************\\n\');
fprintf(\'        <DSP using MATLAB> Exameple 8.29 \\n\\n\');

time_stamp = datestr(now, 31);
[wkd1, wkd2] = weekday(today, \'long\');
fprintf(\'      Now is %20s, and it is %8s  \\n\\n\', time_stamp, wkd2);
%% ------------------------------------------------------------------------

% Digital Filter Specifications:   Elliptic bandpass
ws = [0.3*pi 0.75*pi];           % digital stopband freq in rad
wp = [0.4*pi 0.6*pi];            % digital passband freq in rad
Rp = 1;                          % passband ripple in dB
As = 40;                         % stopband attenuation in dB

% Calculation of Elliptic filter parameters:
[N, wn] = ellipord(wp/pi, ws/pi, Rp, As);

fprintf(\'\\n  ********* Elliptic Filter Order is = %3.0f \\n\', N)

% Digital Elliptic Bandpass Filter Design:
[bhp, ahp] = ellip(N, Rp, As, wn);

[C, B, A] = dir2cas(bhp, ahp)

% Calculation of Frequency Response:
%[dblp, maglp, phalp, grdlp, wwlp] = freqz_m(blp, alp);
[dbhp, maghp, phahp, grdhp, wwhp] = freqz_m(bhp, ahp);


%% -----------------------------------------------------------------
%%                             Plot
%% -----------------------------------------------------------------  

figure(\'NumberTitle\', \'off\', \'Name\', \'Exameple 8.29\')
set(gcf,\'Color\',\'white\'); 
M = 1;                          % Omega max

subplot(2,2,1); plot(wwhp/pi, maghp); axis([0, M, 0, 1.2]); grid on;
xlabel(\' frequency in \\pi units\'); ylabel(\'|H|\'); title(\'Magnitude Response\');
set(gca, \'XTickMode\', \'manual\', \'XTick\', [0, 0.3, 0.4, 0.6, 0.75, M]);
set(gca, \'YTickMode\', \'manual\', \'YTick\', [0, 0.8913, 1]);

subplot(2,2,2); plot(wwhp/pi, dbhp); axis([0, M, -50, 2]); grid on;
xlabel(\' frequency in \\pi units\'); ylabel(\'Decibels\'); title(\'Magnitude in dB\');
set(gca, \'XTickMode\', \'manual\', \'XTick\', [0, 0.3, 0.4, 0.6, 0.75, M]);
set(gca, \'YTickMode\', \'manual\', \'YTick\', [-50, -40, -1, 0]);

subplot(2,2,3); plot(wwhp/pi, phahp/pi); axis([0, M, -1.1, 1.1]); grid on;
xlabel(\'frequency in \\pi nuits\'); ylabel(\'radians in \\pi units\'); title(\'Phase Response\');
set(gca, \'XTickMode\', \'manual\', \'XTick\', [0, 0.3, 0.4, 0.6, 0.75, M]);
set(gca, \'YTickMode\', \'manual\', \'YTick\', [-1:0.5:1]);

subplot(2,2,4); plot(wwhp/pi, grdhp); axis([0, M, 0, 40]); grid on;
xlabel(\'frequency in \\pi units\'); ylabel(\'Samples\'); title(\'Group Delay\');
set(gca, \'XTickMode\', \'manual\', \'XTick\', [0, 0.3, 0.4, 0.6, 0.75, M]);
set(gca, \'YTickMode\', \'manual\', \'YTick\', [0:10:40]);

　　运行结果：

           注意，设计的滤波器是阶数为10。频率响应如下图，