CentOS 7 网卡bond配置

Posted 2020-08-08

对p1p1 p1p2两张网卡做bond步骤

1) 做之前请对各网卡配置进行备份

1 使用root账号登录服务器

2 cp p1p1 p1p2 网卡的初始配置到tmp 目录下，进行备份。

--------------------------------------------------------------

[[email protected] ~]#  cd  /etc/sysconfig/network-scripts/

[[email protected]  network-scripts]# cp ifcfg-p1p1 /tmp

[[email protected]  network-scripts]# cp ifcfg-p1p2 /tmp

--------------------------------------------------------------

2) 使用nmcli命令配置bond

生成bond配置

--------------------------------------------------------------

nmcli con add type bond ifname bond0 mode 1

nmcli con add type bond-slave ifname p1p1 master  bond0

nmcli con add type bond-slave ifname p1p2 master  bond0

注：p1p1 p1p2 为物理网卡的名字

bond的mode如下：

balance-rr (0)  --轮询模式（bond默认的模式）

active-backup (1)  --主备模式（常用）

balance-xor (2)  

broadcast (3) 

802.3ad  (4) --聚合模式

balance-tlb (5) 

balance-alb (6)

--------------------------------------------------------------

3) 修改bond0网卡配置

修改下面表格中标红的内容

---------------------------------------------------------------

cd /etc/sysconfig/network-scripts

[[email protected] network-scripts]# vim ifcfg-bond-bond0

DEVICE=bond0

BONDING_OPTS=mode=active-backup

TYPE=Bond

BONDING_MASTER=yes

BOOTPROTO=static    ---将原来的dhcp 改成static

DEFROUTE=yes

PEERDNS=yes

PEERROUTES=yes

IPV4_FAILURE_FATAL=no

NAME=bond-bond0

UUID=f4146d29-d694-4f13-ae59-56f940c7d120

ONBOOT=yes

IPADDR=192.168.80.7    ---配置分配给服务器的IP地址

PREFIX=24    --配置子网掩码

GATEWAY=192.168.80.1   ---配置网关

 

保存并退出

---------------------------------------------------------------

4) 重启网络

systemctl restart network –重启网络服务

cat /proc/net/bonding/bond0  ---查看bond0接口的相关信息

----------------------------------------------------------------

[[email protected] network-scripts]#  cat /proc/net/bonding/bond0

Ethernet Channel Bonding Driver: v3.7.1 (April 27,  2011)

 

Bonding Mode: fault-tolerance (active-backup)

Primary Slave: None

Currently Active Slave: p1p2

MII  Status: up

MII Polling Interval (ms): 100

Up Delay (ms): 0

Down Delay (ms): 0

 

Slave Interface: p1p1

MII  Status: up

Speed: 10000 Mbps

Duplex: full

Link Failure Count: 2

Permanent HW addr: f4:e9:d4:9a:f1:a0

Slave queue ID: 0

 

Slave Interface: p1p2

MII Status: up

Speed: 10000 Mbps

Duplex: full

Link Failure Count: 2

Permanent HW addr: f4:e9:d4:9a:f1:a2

Slave queue ID: 0

----------------------------------------------------------------

---到此就完成bond配置了---

本文出自 “goodlife” 博客，请务必保留此出处http://g00dlife.blog.51cto.com/12052420/1851628