HP COMPAQ DC 7900中的64位虚拟机

Posted 2021-02-24

is not Code, is configuration steps for use COMPAQ DC 7900 for virtualization machines in 64 Bits

Enable AMT&VT on HP dc7800 & dc7900
 
The HP Compaq dc7800/dc7900 Business PC uses Intel vPro technology to simplify back-office management and reduce IT-related expenditures. Intel vPro technology is a combination of Active Management Technology (AMT) and Intel Virtualization Technology (IVT), which allows for improved management of PC systems and better security.
 
AMT provides Out-of-Band (OOB) remote access to a system regardless of the state of the operating system or power state as long as the system has AC power and is connected to a network. AMT is a hardware and firmware platform resident solution relying upon the Manageability Engine (ME) within the chipset.
 
By default, AMT is disabled in the ME firmware. AMT must be enabled in the ME firmware and configured before the system can benefit from it features.
 
Below are the specific steps to enable AMT on your dc7800/dc7900 machine:
 
On first boot: 
When prompted, press F10 to enter the system Bios configuration
 
    Select Storage-> Boot Order
        disable hard drive and network controller booting options.
        the only option remaining should be 
        USB device, if you're using a usb stick. 
        CD-ROM device, if you're using a CD-ROM.
    Select Security -> System Security
        Virtualization Technology (VTx) == Enabled
        Virtualization Technology Directed I/O (VTd) == Enabled
    Select Advanced-> Power-On Options
        For DC7800:
            After Power Loss == On
            MEBx Setup Prompt == Displayed
        For DC7900:
            After Power Loss == On
            Select Advanced -> Management Operations
                MEBx Setup Prompt == Displayed
    Select File -> Save Changes & Exit
 
Reboot system. 
When prompted, press Ctrl-P for MEBx configuration (i.e. AMT).
 
    The default username/password is admin/admin.
    You are immediately prompted to configure a new password.
    This are guidelines for the Intel ME strong password:
        between 8- and 32-characters long
        contain both upper and lower case Latin characters
        have at least one numeric character
        have at least one ASCII non-alphanumeric character: (!,@,#,$,%,^,&,*,),()
    Save new password.
 
In the main MEBx menu Select Intel(R) ME Configuration
 
    Select 'Intel(R) ME State Control'
        Set it ENABLED
        Select Return to Previous Menu
    Select 'Intel(R) ME Firmware Local Update Qualifier'
        Set it to ALWAYS OPEN
        Select Return to Previous Menu
    Select 'Intel(R) ME Features Control'
        Select 'Manageability Feature Selection'
            Choose 'Intel(R) AMT'
        Select Return to Previous menu
    Select 'Intel(R) ME Power Control'
        Select 'Intel (R) ME ON in Host Sleep States'
            Set the 'widest' range of Sleep States
            Hit 'ESC' to Exit.
    The system will automatically reboot now.
 
When prompted, press Ctrl-P for MEBx configuration (i.e. AMT). 
Select 'Intel(R) AMT Configuration'
 
    NOTE: If you are choosing static IP, you have to have separate Host Name & IP Address for Intel ME than your host CPU. If you are choosing DHCP, you can use the same Host Name and IP Address for Intel ME as the host CPU.  The directions below are for DHCP configuration.
    Select 'Host Name' and enter the same name as for the OS Host name
        For instance, if your hostname is 'planetlab1.site.edu', enter 'planetlab1'.
    Select 'TCP/IP' 
        For the DC7800
            Hit 'N' to enable the Network Interface
        For BOTH
            Hit 'N' to enable DHCP
            provide your domain name as set (or to be set) in the OS.
            For instance, if your hostname is 'planetlab1.site.edu', enter 'planetlab1.site.edu'.
    Select 'Provision Model'
        For the DC7800
            Hit 'N' to not change to AMT 1.0 Mode
            Hit 'Y; to change to Small Business
        For the DC7900
            Select 'Small Business' and hit ENTER.
    Select 'SOL/IDE-R'
        Hit 'Y' to confirm the warning
        Set Username & Password to ENABLED (if it's set to ENABLED don't hit just 'ENTER' because you disable it)
        Set Serial Over LAN to ENABLED
        Set IDE Redirection to ENABLED
    Select 'Secure Firmware Update'
        Set it to ENABLED
    Hit 'ESC' to Exit. The system will reboot again.
 
Power off the system. 
Power back on, to boot from the PlanetLab BootImage.