-Project 2 Cache Controller

Posted javapythonc

tags:

篇首语:本文由小常识网(cha138.com)小编为大家整理,主要介绍了-Project 2 Cache Controller相关的知识,希望对你有一定的参考价值。


2018-Project 2 Cache Controller
1 Purpose
This project is intended to help you to understand the cache architecture and its mechanism.
2 Problem
In this project, you will design a first-level data cache controller with Verilog HDL step by
step. You may need to review the knowledge about the language to make sure you can finish the
project smoothly.
3 Cache characteristics and mechanism
The TMS320C621x/C671x DSP has a two-level memory architecture for program and data,
the first-level program cache (L1P), the first-level data cache (L1D), and the second-level memory
(L2). In this project, you only need to concern about the L1D cache. Table 1 lists some specific
parameters that may be used in this project.
Table 1
Note1: When a dirty block is replaced, the whole L1D cache line must be written back, but the
L1D to L2 write path width is only 32 bit, i.e. you need to repeat 8 times to complete. Similarly,
one load from L2 cache returns 128 bytes of data and you need to repeat 8 times to complete.
Note2: For simplicity, you can assume an infinite write buffer, and ignore TLB. Besides, assume
only one ld/st is permitted to be processed at a time.
4 State machine design
In the first step of designing a cache controller, you need to design a state machine. You need
to consider how many states you need, what functions each state realized, and how the states
transfer to each other.
(1) Draw a state diagram, assign each state a unique binary code to indicate, and mark the
transition condition signal.
2Cache Controller作业代做、代写c/c++,Java程序语言作业、Verilog HDL作业代做
(2) According to your state diagram, list a state transition table, which gives the next state of each
current state based on all the possible condition signals. You must make sure all of the state codes
that may show up in real circuit are listed in the table (including the ones that don’t show up in
your state diagram).
(3) Draw a flow diagram of your cache controller. This is very helpful for your design later.
Hints:
The functionality of L1D cache is to accomplish the processing of two kinds of instructions:
Ld and St. When you need to write back or load data from L2 cache, you will probably need more
than one cycles (also more than one states).
You can reference your supplementary materials of your lecture, Digital System Design I, to
review the knowledge about state machine.
5 Circuit design
Based on your flow diagram, design your cache controller and draw the circuit. You should
indicate the important signals aside their wires, and make a list beside the diagram showing the
meaning and function of each signal (with their source and destination if necessary).
Hints:
You can realize the cache controller based on a counter or a few mux. If you chose to design
based on counter, then the counter’s different states map to different states in your design. You
only need to add some logic to make it transform properly and give right output signals. If you
chose to design based on mux, you should use a few mux (the number of which is equal to the
width of your state code). The current state code is used as the selective signal to all the mux, and
you need to give each mux proper inputs so that it outputs the right signal. And the combination of
the outputs of all the mux gives the next state code.
6 Verilog HDL realization
Since you have already completed the circuit design, you can easily describe the circuit in
Verilog HDL. Please add enough notes to make your program easy to understand, because this
might affect your mark. You should focus on description of behavior, and add some description of
structure and data stream if necessary.
Remember that what you should focus is the output control signals and the states change of
cache controller; you can ignore the specific data.
The module name and some of the signal names are given below, you must not change these
names in your program.
module cache_controller(…);
input ld, st;
input addr[31:0];
input tag_loaded[20:0], valid, dirty;
input l2_ack;
output hit, miss;
output load_ready, write_l1;
output read_l2, write_l2;
3
signal meaning:
ld/st – load or store request
addr[31:0] – cache access address
tag_loaded[18:0] – the tag of the indexed cache data address
valid – valid indication of the block in cache
dirty – indicate whether the cache line is dirty
l2_ack – indicate that the data loaded from L2 cache is arrived
hit/miss – indicate the access is a hit or miss (these signals are used to make your design
understandable)
load_ready – indicate the data is successfully loaded and the data is ready for processor
write_l1 – enable for L1 cache write
read_l2 – load request to L2 cache
write_l2 – enable for write back to write buffer
Note: All of your work must be presented in electronic version, including the diagram drawing.
You can make use of certain software to do that. And describe your design process in as much
detail as you can in the report.
Requirement: A report (word or pdf) on your step-by-step implementation of the above processes,
and your Verilog HDL code.
Deadline: 2019.1.13 24:00
Compress your files into a rar (or zip) format named by your student ID and name, for
example 3160101234_yourname_project2, and send the format to [email protected] If you
want to modify your program, you can send it again before the deadline and add “version2” after
the filename, for example 3160101234_yourname_project2_version2.
If you have any question, send an email to [email protected] .
No Copy! The same reports or codes will both get zero scores.

因为专业,所以值得信赖。如有需要,请加QQ99515681 或邮箱:[email protected] 

微信:codinghelp




























































































以上是关于-Project 2 Cache Controller的主要内容,如果未能解决你的问题,请参考以下文章

php输出控制output controll(header, ob_xxx)

html http://stackoverflow.com/questions/40976125/linking-directly-to-both-parentchild-views-controll

Laravel (7) Resource Policies don't work with CamelCase, get a 403 for view policy (show in controll

ASP.NET MVC 复制MVC项目代码到同一个项目的时候报错The request for ‘home’ has found the following matching controll(代码片

ubuntu修改键盘键位映射

NSFetchResultsController -controllerDidChangeContent: - 尝试使用 userInfo 为单元格创建两个动画