华为NE40E路由器实验配置示例 | 配置EVdPdNd L3VdPdNdv6 over SRv6 BE
Posted COCOgsta
tags:
篇首语：本文由小常识网(cha138.com)小编为大家整理，主要介绍了华为NE40E路由器实验配置示例 | 配置EVdPdNd L3VdPdNdv6 over SRv6 BE相关的知识，希望对你有一定的参考价值。
组网需求
如图1所示：PE1、P和PE2属于同一自治系统，要求它们之间通过IS-IS协议达到IPv6网络互连的目的。在PE1和PE2之间通过建立双向SRv6 BE承载EVPN L3VPNv6业务。
图1 配置EVPN L3VPNv6 over SRv6 BE组网图
配置思路
-
使能PE1、P和PE2各接口的IPv6转发能力，配置各接口的IPv6地址。
-
在PE1、P和PE2上使能IS-IS，配置Level级别，指定网络实体。
-
在PE设备上配置IPv6 L3VPN实例并将IPv6 L3VPN实例绑定到接入侧接口。
- 在PE设备之间建立BGP EVPN对等体关系。
-
在PE设备上配置SRv6 BE。配置IS-IS的SRv6能力。
操作步骤
1. 使能各接口的IPv6转发能力，配置IPv6地址，以PE1为例，其他设备的配置过程相同，不再赘述
<HUAWEI> system-view
[~HUAWEI] sysname PE1
[*HUAWEI] commit
[~PE1] interface gigabitethernet 1/0/0
[~PE1-GigabitEthernet1/0/0] ipv6 enable
[*PE1-GigabitEthernet1/0/0] ipv6 address 2001:DB8:10::1 64
[*PE1-GigabitEthernet1/0/0] quit
[*PE1] interface LoopBack 1
[*PE1-LoopBack1] ipv6 enable
[*PE1-LoopBack1] ipv6 address 2001:DB8:1::1 128
[*PE1-LoopBack1] quit
[*PE1] commit2. 配置IS-IS
# 配置PE1。
[~PE1] isis 1
[*PE1-isis-1] is-level level-1
[*PE1-isis-1] cost-style wide
[*PE1-isis-1] network-entity 10.0000.0000.0001.00
[*PE1-isis-1] ipv6 enable topology ipv6
[*PE1-isis-1] quit
[*PE1] interface gigabitethernet 1/0/0
[*PE1-GigabitEthernet1/0/0] isis ipv6 enable 1
[*PE1-GigabitEthernet1/0/0] quit
[*PE1] interface loopback1
[*PE1-LoopBack1] isis ipv6 enable 1
[*PE1-LoopBack1] quit
[*PE1] commit# 配置P。
[~P] isis 1
[*P-isis-1] is-level level-1
[*P-isis-1] cost-style wide
[*P-isis-1] network-entity 10.0000.0000.0002.00
[*P-isis-1] ipv6 enable topology ipv6
[*P-isis-1] quit
[*P] interface gigabitethernet 1/0/0
[*P-GigabitEthernet1/0/0] isis ipv6 enable 1
[*P-GigabitEthernet1/0/0] quit
[*P] interface gigabitethernet 2/0/0
[*P-GigabitEthernet2/0/0] isis ipv6 enable 1
[*P-GigabitEthernet2/0/0] quit
[*P] interface loopback1
[*P-LoopBack1] isis ipv6 enable 1
[*P-LoopBack1] quit
[*P] commit# 配置PE2。
[~PE2] isis 1
[*PE2-isis-1] is-level level-1
[*PE2-isis-1] cost-style wide
[*PE2-isis-1] network-entity 10.0000.0000.0003.00
[*PE2-isis-1] ipv6 enable topology ipv6
[*PE2-isis-1] quit
[*PE2] interface gigabitethernet 1/0/0
[*PE2-GigabitEthernet1/0/0] isis ipv6 enable 1
[*PE2-GigabitEthernet1/0/0] quit
[*PE2] interface loopback1
[*PE2-LoopBack1] isis ipv6 enable 1
[*PE2-LoopBack1] quit
[*PE2] commit配置完成后，可按如下指导检查IS-IS是否配置成功。
# 显示IS-IS邻居信息。以PE1为例。
[~PE1] display isis peer
Peer information for ISIS(1)
System Id Interface Circuit Id State HoldTime Type PRI
--------------------------------------------------------------------------------
0000.0000.0002* GE1/0/0 0000.0000.0002.01 Up 8s L1 64
Total Peer(s): 13. 在PE设备上配置IPv6 L3VPN实例并将IPv6 L3VPN实例绑定到接入侧接口
# 配置PE1。
[~PE1] ip vpn-instance vpn1
[*PE1-vpn-instance-vpn1] ipv6-family
[*PE1-vpn-instance-vpn1-af-ipv6] route-distinguisher 100:1
[*PE1-vpn-instance-vpn1-af-ipv6] vpn-target 1:1 evpn
[*PE1-vpn-instance-vpn1-af-ipv6] quit
[*PE1-vpn-instance-vpn1] quit
[*PE1] interface gigabitethernet2/0/0
[*PE1-GigabitEthernet2/0/0] ip binding vpn-instance vpn1
[*PE1-GigabitEthernet2/0/0] ipv6 enable
[*PE1-GigabitEthernet2/0/0] ipv6 address 2001:DB8:11::1 64
[*PE1-GigabitEthernet2/0/0] quit
[*PE1] bgp 100
[*PE1-bgp] ipv6-family vpn-instance vpn1
[*PE1-bgp-6-vpn1] import-route direct
[*PE1-bgp-6-vpn1] advertise l2vpn evpn
[*PE1-bgp-6-vpn1] quit
[*PE1-bgp] quit
[*PE1] commit# 配置PE2。
[~PE2] ip vpn-instance vpn1
[*PE2-vpn-instance-vpn1] ipv6-family
[*PE2-vpn-instance-vpn1-af-ipv6] route-distinguisher 200:1
[*PE2-vpn-instance-vpn1-af-ipv6] vpn-target 1:1 evpn
[*PE2-vpn-instance-vpn1-af-ipv6] quit
[*PE2-vpn-instance-vpn1] quit
[*PE2] interface gigabitethernet2/0/0
[*PE2-GigabitEthernet2/0/0] ip binding vpn-instance vpn1
[*PE2-GigabitEthernet2/0/0] ipv6 enable
[*PE2-GigabitEthernet2/0/0] ipv6 address 2001:DB8:22::1 64
[*PE2-GigabitEthernet2/0/0] quit
[*PE2] bgp 100
[*PE2-bgp] ipv6-family vpn-instance vpn1
[*PE2-bgp-6-vpn1] import-route direct
[*PE2-bgp-6-vpn1] advertise l2vpn evpn
[*PE2-bgp-6-vpn1] quit
[*PE2-bgp] quit
[*PE2] commit4. 在PE设备之间建立BGP EVPN对等体关系
# 配置PE1。
[~PE1] bgp 100
[~PE1-bgp] router-id 1.1.1.1
[*PE1-bgp] peer 2001:DB8:3::3 as-number 100
[*PE1-bgp] peer 2001:DB8:3::3 connect-interface loopback 1
[*PE1-bgp] l2vpn-family evpn
[*PE1-bgp-af-evpn] peer 2001:DB8:3::3 enable
[*PE1-bgp-af-evpn] quit
[*PE1-bgp] quit
[*PE1] commit# 配置PE2。
[~PE2] bgp 100
[~PE2-bgp] router-id 3.3.3.3
[*PE2-bgp] peer 2001:DB8:1::1 as-number 100
[*PE2-bgp] peer 2001:DB8:1::1 connect-interface loopback 1
[*PE2-bgp] l2vpn-family evpn
[*PE2-bgp-af-evpn] peer 2001:DB8:1::1 enable
[*PE2-bgp-af-evpn] quit
[*PE2-bgp] quit
[*PE2] commit配置完成后，在PE设备上执行display bgp evpn peer命令，可以看到PE之间的BGP EVPN对等体关系已建立，并达到Established状态。
5. 在PE设备之间建立SRv6 BE
# 配置PE1。
[~PE1] segment-routing ipv6
[*PE1-segment-routing-ipv6] encapsulation source-address 2001:DB8:1::1
[*PE1-segment-routing-ipv6] locator PE1 ipv6-prefix 2001:DB8:100:: 64 static 32
[*PE1-segment-routing-ipv6-locator] quit
[*PE1-segment-routing-ipv6] quit
[*PE1] isis 1
[*PE1-isis-1] segment-routing ipv6 locator PE1
[*PE1-isis-1] quit
[*PE1] bgp 100
[*PE1-bgp] l2vpn-family evpn
[*PE1-bgp-af-evpn] peer 2001:DB8:3::3 advertise encap-type srv6
[*PE1-bgp-af-evpn] quit
[*PE1-bgp] ipv6-family vpn-instance vpn1
[*PE1-bgp-6-vpn1] segment-routing ipv6 locator PE1 evpn
[*PE1-bgp-6-vpn1] segment-routing ipv6 best-effort evpn
[*PE1-bgp-6-vpn1] quit
[*PE1-bgp] quit
[*PE1] commit# 配置PE2。
[~PE2] segment-routing ipv6
[*PE2-segment-routing-ipv6] encapsulation source-address 2001:DB8:3::3
[*PE2-segment-routing-ipv6] locator PE2 ipv6-prefix 2001:DB8:130:: 64 static 32
[*PE2-segment-routing-ipv6-locator] quit
[*PE2-segment-routing-ipv6] quit
[*PE2] isis 1
[*PE2-isis-1] segment-routing ipv6 locator PE2
[*PE2-isis-1] quit
[*PE2] bgp 100
[*PE2-bgp] l2vpn-family evpn
[*PE2-bgp-af-evpn] peer 2001:DB8:1::1 advertise encap-type srv6
[*PE2-bgp-af-evpn] quit
[*PE2-bgp] ipv6-family vpn-instance vpn1
[*PE2-bgp-6-vpn1] segment-routing ipv6 locator PE2 evpn
[*PE2-bgp-6-vpn1] segment-routing ipv6 best-effort evpn
[*PE2-bgp-6-vpn1] quit
[*PE2-bgp] quit
[*PE2] commit6. 检查配置结果
在PE上通过配置命令display bgp evpn all routing-table prefix-route，可以看到远端发来的IP前缀路由。以PE1为例：
[~PE1] display bgp evpn all routing-table prefix-route
Local AS number : 100
BGP Local router ID is 1.1.1.1
Status codes: * - valid, > - best, d - damped, x - best external, a - add path,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
EVPN address family:
Number of Ip Prefix Routes: 2
Route Distinguisher: 200:1
Network(EthTagId/IpPrefix/IpPrefixLen) NextHop
*> 0:[2001:DB8:11::]:64 0.0.0.0
*>i 0:[2001:DB8:22::]:64 2001:DB8:3::3在PE上通过配置命令display ipv6 routing-table vpn-instance vpn1，可以看到远端发来的私网路由。以PE1为例：
[~PE1] display ipv6 routing-table vpn-instance vpn1
Routing Table : vpn1
Destinations : 4 Routes : 4
Destination : 2001:DB8:11:: PrefixLength : 64
NextHop : 2001:DB8:11::1 Preference : 0
Cost : 0 Protocol : Direct
RelayNextHop : :: TunnelID : 0x0
Interface : GigabitEthernet2/0/0 Flags : D
Destination : 2001:DB8:11::1 PrefixLength : 128
NextHop : ::1 Preference : 0
Cost : 0 Protocol : Direct
RelayNextHop : :: TunnelID : 0x0
Interface : GigabitEthernet2/0/0 Flags : D
Destination : 2001:DB8:22:: PrefixLength : 64
NextHop : 2001:DB8:3::3 Preference : 255
Cost : 0 Protocol : IBGP
RelayNextHop : 2001:DB8:3::3 TunnelID : 0x0
Interface : SRv6 BE Flags : RD
Destination : FE80:: PrefixLength : 10
NextHop : :: Preference : 0
Cost : 0 Protocol : Direct
RelayNextHop : :: TunnelID : 0x0
Interface : NULL0 Flags : DB以上是关于华为NE40E路由器实验配置示例 | 配置EVdPdNd L3VdPdNdv6 over SRv6 BE的主要内容，如果未能解决你的问题，请参考以下文章
华为NE40E路由器实验配置示例 | 配置SR-MPLS BE隧道的TI-LFA FRR功能
华为NE40E路由器实验配置示例 | 配置EVdPdNd VPLS over SR-MPLS BE(BD EVdPdNd)
华为NE40E路由器实验配置示例 | 配置L3VdPdNd over OSPF SR-MPLS BE
华为NE40E路由器实验配置示例 | 配置L3VdPdNd over OSPF SR-MPLS BE