请教，STM32定时器的ETR与外部脉冲计数

Posted 2023-04-28

TIMx需要工作在从模式下，从外部触发计数。
通过TIM_SelectInputTrigger(TIMx, TIM_TI1F_ED)可以选择CH1管脚作为输入。也可以选择CH1或CH2的滤波输入。在从模式下，CH3和CH4不能作为外部触发管脚。 参考技术A 最简单的计数编程原理即可

求个采纳，谢谢你了哦

精准控制PWM脉冲的频率和数量

　　在一些项目中，我们经常要控制PWM脉冲的频率和数量，比如步进电机的控制等，下面分享一个程序是关于这方面的，程序的思想就是通过STM32的定时器来输出PWM波，并开启定时器中断，在中断里面计数脉冲的数量，一旦脉冲数量达到了目标值，就关闭定时器，实现精确控制脉冲的数量。

　　下面是程序分析：

　　定时器4配置

　　

#include"stm32f10x.h"
#include"pwm.h"
/*?¨ê±?÷4ê?3?4?·2?í?????±è??3?
ó2?tá??óè???
CH1--PB6
CH2--PB7
CH3--PB8
CH4--PB9
*/
void PWM_Init(u16 arr,u16 psc)
{
u16 val1=arr/5;
/*u16 val2=arr/4;
u16 val3=arr/6;
u16 val4=arr/8;*/


GPIO_InitTypeDef GPIO_InitStructure;
TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
TIM_OCInitTypeDef TIM_OCInitStructure;

//ê±?ó????
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4 ,ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_AFIO ,ENABLE);




//???ú3?ê??ˉ
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6|GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);

//?¨ê±?÷4?ù±?????
TIM_TimeBaseInitStructure.TIM_Period=arr;
TIM_TimeBaseInitStructure.TIM_Prescaler=psc;
TIM_TimeBaseInitStructure.TIM_ClockDivision=0;
TIM_TimeBaseInitStructure.TIM_CounterMode=TIM_CounterMode_Up;
TIM_TimeBaseInit(TIM4,&TIM_TimeBaseInitStructure);

//PWM?￡ê?????

TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1; //?????¨ê±?÷?￡ê?:TIM??3??í?èμ÷???￡ê?1
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; //±è??ê?3?ê1?ü
TIM_OCInitStructure.TIM_Pulse = 0; //éè??′y×°è?2???±è????′??÷μ???3??μ
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High; //ê?3???D?:TIMê?3?±è????D???
TIM_OC1Init(TIM4, &TIM_OCInitStructure);
TIM_OC1PreloadConfig(TIM4, TIM_OCPreload_Enable); //ê1?üTIMx?úCCR1é?μ??¤×°????′??÷

/*TIM_OCInitStructure.TIM_Pulse=val2;
TIM_OC2Init(TIM4,&TIM_OCInitStructure);
TIM_OC2PreloadConfig(TIM4,TIM_OCPreload_Enable );

TIM_OCInitStructure.TIM_Pulse=val3;
TIM_OC3Init(TIM4,&TIM_OCInitStructure);
TIM_OC3PreloadConfig(TIM4,TIM_OCPreload_Enable );

TIM_OCInitStructure.TIM_Pulse=val4;
TIM_OC4Init(TIM4,&TIM_OCInitStructure);
TIM_OC4PreloadConfig(TIM4,TIM_OCPreload_Enable );*/


TIM_ARRPreloadConfig(TIM4, ENABLE);

TIM_ClearITPendingBit(TIM4, TIM_IT_CC1);
TIM_ITConfig(TIM4,TIM_IT_CC1,ENABLE);

//TIM_Cmd(TIM4,ENABLE);

}
void NVIC_Config(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
NVIC_InitStructure.NVIC_IRQChannel = TIM4_IRQn ;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);

}

　　主函数：

#include "stm32f10x.h"
#include "led.h"
#include "delay.h"
#include "pwm.h"
#include "usart.h"
u32 step=0;
int main(void)
{
SystemInit();
uart_init(115200);
delay_init();
LED_Init();
NVIC_Config();
PWM_Init(719,100);
TIM_Cmd(TIM4,ENABLE);
while(1)
{

// delay_ms(100);
// LED1=!LED1;
// delay_ms(100);
TIM4->CCR1 = 300;

}
}
void TIM4_IRQHandler(void)
{
if(TIM_GetITStatus(TIM4,TIM_IT_CC1)!=RESET)
{
TIM_ClearITPendingBit(TIM4,TIM_IT_CC1);
step++;
printf("%d\r\n",step);
if(step==80000)
{
TIM_Cmd(TIM4,DISABLE);
}
}

}

以上就是完整程序。欢迎同学交流，改正。