6.2.2UE maximum output power reduction-翻译

Posted 2021-07-30 AI浩

1、测试目的

6.2.2.3中确定的RB数量是基于满足立方米制(CM)的最大功率回退(MPR)的要求。

2、测试适用

本测试要求适用于所有类型的NR UE release 15和forward。

3、测试说明

1、初始条件

初始条件是UE需要测试的一组测试配置，以及SS为使UE达到正确的测量状态而采取的步骤。根据表5.3.5-1中NR工作频带的要求，初始测试配置包括环境条件、测试频率和信道带宽。所有这些配置均应使用适用于每个信道带宽和子载波间距的测试参数进行测试，测试参数见表6.2.2.4.1-1至表6.2.2.4.1-9。上行参考测量通道(rmc)的详细信息请参见附件A.2。附件C.2中规定了PDSCH和PDCCH在测量前的配置。

                                   Table 6.2.2.4.1-1: Test Configuration Table (Power Class 1, MPRnarrow)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highest
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				CP-OFDM 64 QAM	Outer_1RB_Left
2	High				CP-OFDM 64 QAM	Outer_1RB_Right
3	Low				CP-OFDM 64 QAM	2@0
4	High				CP-OFDM 64 QAM	2@NRB-2
5	Low				CP-OFDM 64 QAM	7@0
6	High				CP-OFDM 64 QAM	7@NRB-7
NOTE 1:    各射频分配的具体配置如表6.1-2所示。

                             Table 6.2.2.4.1-2: Test Configuration Table (Power Class 1, MPRWT, BWchannel ≤ 200 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, Mid range,High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highest supported channel bandwidth that ≤ 200 MHz
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	8@0
2	High				DFT-s-OFDM PI/2 BPSK	8@NRB-8
3	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
4	Mid				DFT-s-OFDM QPSK	Inner_Full_Region2
5	Low				DFT-s-OFDM QPSK	8@0
6	High				DFT-s-OFDM QPSK	8@NRB-8
7	Mid				DFT-s-OFDM QPSK	Outer_Full
8	Mid				DFT-s-OFDM 16 QAM	Inner_Full_Region2
9	Low				DFT-s-OFDM 16 QAM	8@0
10	High				DFT-s-OFDM 16 QAM	8@NRB-8
11	Mid				DFT-s-OFDM 16 QAM	Outer_Full
12	Low				DFT-s-OFDM 64 QAM	8@0
13	High				DFT-s-OFDM 64 QAM	8@NRB-8
14	Mid				DFT-s-OFDM 64 QAM	Outer_Full
15	Mid				DFT-s-OFDM 64 QAM	Inner_Full_Region2
16	Mid				CP-OFDM QPSK	Inner_Full_Region2
17	Low				CP-OFDM QPSK	8@0
18	High				CP-OFDM QPSK	8@NRB-8
19	Mid				CP-OFDM QPSK	Outer_Full
20	Low				CP-OFDM 16 QAM	8@0
21	High				CP-OFDM 16 QAM	8@NRB-8
22	Mid				CP-OFDM 16 QAM	Outer_Full
23	Mid				CP-OFDM 16 QAM	Inner_Full_Region2
24	Low				CP-OFDM 64 QAM	8@0
25	High				CP-OFDM 64 QAM	8@NRB-8
26	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1:    The specific configuration of each RF allocation is defined in clause 6.1-2.

                       Table 6.2.2.4.1-3: Test Configuration Table (Power Class 1, MPRWT, BWchannel = 400 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, Mid range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					400 MHz
Test SCS as specified in Table 5.3.5-1					120kHz
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	8@0
2	High				DFT-s-OFDM PI/2 BPSK	8@NRB-8
3	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
4	Mid				DFT-s-OFDM PI/2 BPSK	Inner_Full_Region2
5	Mid				DFT-s-OFDM QPSK	Inner_Full_Region2
6	Low				DFT-s-OFDM QPSK	8@0
7	High				DFT-s-OFDM QPSK	8@NRB-8
8	Default				DFT-s-OFDM QPSK	Outer_Full
9	Mid				DFT-s-OFDM 16 QAM	Inner_Full_Region2
10	Low				DFT-s-OFDM 16 QAM	8@0
11	High				DFT-s-OFDM 16 QAM	8@NRB-8
12	Mid				DFT-s-OFDM 16 QAM	Outer_Full
13	Low				DFT-s-OFDM 64 QAM	8@0
14	High				DFT-s-OFDM 64 QAM	8@NRB-8
15	Mid				DFT-s-OFDM 64 QAM	Outer_Full
16	Mid				CP-OFDM QPSK	Inner_Full_Region2
17	Low				CP-OFDM QPSK	8@0
18	High				CP-OFDM QPSK	8@NRB-8
19	Mid				CP-OFDM QPSK	Outer_Full
20	Low				CP-OFDM 16 QAM	8@0
21	High				CP-OFDM 16 QAM	8@NRB-8
22	Mid				CP-OFDM 16 QAM	Outer_Full
23	Mid				CP-OFDM 16 QAM	Inner_Full_Region2
24	Low				CP-OFDM 64 QAM	8@0
25	High				CP-OFDM 64 QAM	8@NRB-8
26	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1:    The specific configuration of each RF allocation is defined in clause 6.1-2.

 

Table 6.2.2.4.1-4: Void

Table 6.2.2.4.1-5: Void

Table 6.2.2.4.1-6: Void

 

                       Table 6.2.2.4.1-7: Test Configuration Table (Power Class 2, 3 and 4, MPRnarrow, BWchannel ≤ 200 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highes supported channel bandwidth that ≤ 200 MHz t
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Left
2	High				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Right
3	Low				DFT-s-OFDM QPSK	Outer_1RB_Left
4	High				DFT-s-OFDM QPSK	Outer_1RB_Right
NOTE 1:    The specific configuration of each RF allocation is defined in Table 6.1-1.

 

                         Table 6.2.2.4.1-8: Test Configuration Table (Power Class 2, 3 and 4, MPRWT, BWchannel ≤ 200 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, Mid range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highest supported channel bandwidth that ≤ 200 MHz
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
2	Mid				DFT-s-OFDM QPSK	Outer_Full
3	Mid				DFT-s-OFDM 16 QAM	Inner_Full
4	Low				DFT-s-OFDM 16 QAM	Outer_1RB_Left
5	High				DFT-s-OFDM 16 QAM	Outer_1RB_Right
6	Mid				DFT-s-OFDM 16 QAM	Outer_Full
7	Mid				DFT-s-OFDM 64 QAM	Inner_Full
8	Low				DFT-s-OFDM 64 QAM	Outer_1RB_Left
9	High				DFT-s-OFDM 64 QAM	Outer_1RB_Right
10	Mid				DFT-s-OFDM 64 QAM	Outer_Full
11	Mid				CP-OFDM QPSK	Inner_Full
12	Low				CP-OFDM QPSK	Outer_1RB_Left
13	High				CP-OFDM QPSK	Outer_1RB_Right
14	Mid				CP-OFDM QPSK	Outer_Full
15	Low				CP-OFDM 16 QAM	Outer_1RB_Left
16	High				CP-OFDM 16 QAM	Outer_1RB_Right
17	Mid				CP-OFDM 16 QAM	Outer_Full
18	Low				CP-OFDM 64 QAM	Outer_1RB_Left
19	High				CP-OFDM 64 QAM	Outer_1RB_Right
20	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1:    The specific configuration of each RF allocation is defined in Table 6.1-1.

                        Table 6.2.2.4.1-9: Test Configuration Table (Power Class 2, 3 and 4, MPRWT, BWchannel = 400 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					400 MHz
Test SCS as specified in Table 5.3.5-1					120kHz
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Left
2	High				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Right
3	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
4	Low				DFT-s-OFDM QPSK	Outer_1RB_Left
5	High				DFT-s-OFDM QPSK	Outer_1RB_Right
6	Mid				DFT-s-OFDM QPSK	Outer_Full
7	Low				DFT-s-OFDM 16 QAM	Outer_1RB_Left
8	High				DFT-s-OFDM 16 QAM	Outer_1RB_Right
9	Mid				DFT-s-OFDM 16 QAM	Outer_Full
10	Low				DFT-s-OFDM 64 QAM	Outer_1RB_Left
11	High				DFT-s-OFDM 64 QAM	Outer_1RB_Right
12	Mid				DFT-s-OFDM 64 QAM	Outer_Full
13	Low				CP-OFDM QPSK	Outer_1RB_Left
14	High				CP-OFDM QPSK	Outer_1RB_Right
15	Mid				CP-OFDM QPSK	Outer_Full
16	Low				CP-OFDM 16 QAM	Outer_1RB_Left
17	High				CP-OFDM 16 QAM	Outer_1RB_Right
18	Mid				CP-OFDM 16 QAM	Outer_Full
19	Low				CP-OFDM 64 QAM	Outer_1RB_Left
20	High				CP-OFDM 64 QAM	Outer_1RB_Right
21	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1:    The specific configuration of each RF allocation is defined in Table 6.1-1.

 

2、测试步骤

1.SS通

以上是关于6.2.2UE maximum output power reduction-翻译的主要内容，如果未能解决你的问题，请参考以下文章

leetCode-Maximum Average Subarray I

什么是FCST，PO，FC？？是关于材料管理的！！！

670. Maximum Swap

152. Maximum Product Subarray

628. Maximum Product of Three Numbers

628. Maximum Product of Three Numbers