RationalDMIS2022阵列工件测量

Posted 山涧果子

tags:

篇首语：本文由小常识网(cha138.com)小编为大家整理，主要介绍了RationalDMIS2022阵列工件测量相关的知识，希望对你有一定的参考价值。


RationalDMIS2022阵列工件测量_d3


RationalDMIS2022阵列工件测量_d3_02


RationalDMIS2022阵列工件测量_DMIS_03

$$/*  Header
DMISMN/Created by [爱科腾瑞科技(北京)有限公司-091522-DEMO-11022(华清)] on 星期二, 七月 05, 2022, 4.0
UNITS/MM, ANGDEC, MMPS
WKPLAN/XYPLAN
PRCOMP/ON
TECOMP/ON
FLY/1.0000
MODE/MAN
SNSET/APPRCH, 2.0000
SNSET/RETRCT, 2.0000
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, 20.0000
RECALL/D(MCS)
SNSLCT/S(D2L30)
GEOALG/BF, LSTSQR
GEOALG/ANGLB, DEFALT
GEOALG/CIRCLE, MINMAX
GEOALG/ARC, LSTSQR
GEOALG/PLANE, LSTSQR
$$
$$
$$*/
MODE/MAN

$$粗建夹具坐标系

F(PLN1)=FEAT/PLANE,CART,140.6036,71.5915,-30.0000,0.0000,0.0000,1.0000
$$ Measurement points are created through nominal points
MEAS/PLANE, F(PLN1), 3
  PTMEAS/CART,  28.1149, 182.1369, -30.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 111.6027,  15.6215, -30.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 282.0933,  17.0162, -30.0000, 0.0000, 0.0000, 1.0000
ENDMES
F(LN1)=FEAT/LINE,BND,CART,8.4089,0.0000,-33.7275,254.2380,0.0000,-33.9379,0.0000,-1.0000,0.0000
$$ Measurement points are created through nominal points
MEAS/LINE, F(LN1), 2
  PTMEAS/CART,   8.4089, 0.0000, -33.7275, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 254.2380, 0.0000, -33.9379, 0.0000, -1.0000, 0.0000
ENDMES
F(PT1)=FEAT/POINT,CART,0.0000,6.2533,-34.8850,-1.0000,-0.0000,-0.0000
MEAS/POINT, F(PT1), 1
  PTMEAS/CART, 0.0000,6.2533,-34.8850,-1.0000,-0.0000,-0.0000
ENDMES
D(CRD1) = DATSET/FA(PLN1), ZDIR, ZORIG, FA(LN1), XDIR, YORIG, FA(PT1), XORIG
D(CRD1) = TRANS/ZORIG, 30, YORIG, -0, XORIG, -0
$$ Set.CAD2PCS.CADM_1
MODE/PROG,MAN

$$精建夹具坐标系

SNSET/APPRCH, 2.0000
SNSET/RETRCT, 2.0000
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, FA(PLN1), 40
F(PLN2)=FEAT/PLANE,CART,277.6282,238.0852,-30.0000,0.0000,0.0000,1.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, -3.0000, 6.2533, 11.0000
MEAS/PLANE, F(PLN2), 4
  GOTO/CART,    -3.0000,   6.2533,  11.0000
  GOTO/CART,   123.3417,  30.8108,  11.0000
  PTMEAS/CART, 123.3417,  30.8108, -30.0000, 0.0000, 0.0000, 1.0000
  GOTO/CART,   123.3417,  30.8108,  11.0000
  GOTO/CART,   434.8503,  28.4933,  11.0000
  PTMEAS/CART, 434.8503,  28.4933, -30.0000, 0.0000, 0.0000, 1.0000
  GOTO/CART,   434.8503,   8.4933,  11.0000
  GOTO/CART,   430.2475, 439.6372,  11.0000
  PTMEAS/CART, 430.2475, 439.6372, -30.0000, 0.0000, 0.0000, 1.0000
  GOTO/CART,   430.2475, 439.6372,  11.0000
  GOTO/CART,   122.0735, 453.3996,  11.0000
  PTMEAS/CART, 122.0735, 453.3996, -30.0000, 0.0000, 0.0000, 1.0000
  GOTO/CART,   122.0735, 453.3996,  11.0000
ENDMES
D(CRD2) = DATSET/FA(PLN2), ZDIR
F(LN2)=FEAT/LINE,BND,CART,109.9386,0.0000,-34,428.4369,0.0000,-34,0.0000,-1.0000,0.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 122.0735, 453.3996, 11.0000
MEAS/LINE, F(LN2), 2
  GOTO/CART,   122.0735, 453.3996,  11.0000
  GOTO/CART,   109.9386,  -3.0000,  11.0000
  PTMEAS/CART, 109.9386,   0.0000, -34, 0.0000, -1.0000, 0.0000
    GOTO/CART, 109.9386, 0,  11.0000
  GOTO/CART,   428.4369,  0,  11.0000
  PTMEAS/CART, 428.4369,   0.0000, -34, 0.0000, -1.0000, 0.0000
ENDMES
F(LN3)=FEAT/LINE,BND,CART,0.0000,105.3507,-34,0.0000,392.1329,-34,-1.0000,0.0000,0.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 428.4369, -3.0000, 11.0000
MEAS/LINE, F(LN3), 2
  GOTO/CART,   428.4369,  -3.0000,  11.0000
  GOTO/CART,    -3.0000, 105.3507,  11.0000
  PTMEAS/CART,   0.0000, 105.3507, -34, -1.0000, -0.0000, -0.0000
   GOTO/CART,   0, 105.3507,  11.0000
  GOTO/CART,    0, 392.1329,  11.0000
  PTMEAS/CART,   0.0000, 392.1329, -34, -1.0000, -0.0000, -0.0000
ENDMES
F(PT_INTER1)=FEAT/POINT,CART,0.0000,0.0000,-34.0000,0.0000,0.0000,1.0000
CONST/POINT,F(PT_INTER1),INTOF,FA(LN2),FA(LN3)
D(CRD3) = DATSET/FA(PLN2), ZDIR, ZORIG, FA(LN2), XDIR, FA(PT_INTER1), XORIG
D(CRD3) = TRANS/ZORIG, 30, YORIG, FA(PT_INTER1), XORIG, -0
$$ Set.CAD2PCS.CADM_1

GOTO/-3.0000, 392.1329, 16.0000

DECL/COMMON,INTGR,I

I = ASSIGN/1

DECL/COMMON,INTGR,J

J = ASSIGN/1


DO/I,1,3,1

DO/J,1,4,1

RECALL/D(CRD3)

D(CRD8) = TRANS/YORIG, 200*(I-1)

D(CRD9) = TRANS/XORIG, 150*(J-1)


$$
MODE/PROG,MAN

$$粗建零件坐标系
GOTO/0.0000, 0.0000, 30.0000
F(PLN3)=FEAT/PLANE,CART,23.2124,45.5878,-0.0000,0.0000,0.0000,1.0000
$$ Measurement points are created through actual points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 5.5666, 11.1639, 4.0000
MEAS/PLANE, F(PLN3), 3
  PTMEAS/CART,  5.5666, 11.1639, 0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART,  4.8649, 58.0332, 0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 59.2058, 67.5662, 0.0000, 0.0000, 0.0000, 1.0000
ENDMES
D(CRD4) = DATSET/FA(PLN3), ZDIR, ZORIG
D(CRD4) = TRANS/ZORIG, -0
F(LN4)=FEAT/LINE,BND,CART,5.6510,0.0000,-3.1570,59.9447,0.0000,-2.9202,0.0000,-1.0000,0.0000
$$ Measurement points are created through actual points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 5.6510, -4.0000, -3.1570
MEAS/LINE, F(LN4), 2
  PTMEAS/CART,  5.6510, 0.0000, -3.1570, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 59.9447, 0.0000, -2.9202, 0.0000, -1.0000, 0.0000
ENDMES
F(PT2)=FEAT/POINT,CART,0.0000,4.0319,-2.8525,-1.0000,-0.0000,-0.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, -3.0000, 4.0319, -2.8525
MEAS/POINT, F(PT2), 1
  PTMEAS/CART, 0.0000,4.0319,-2.8525,-1.0000,-0.0000,-0.0000
ENDMES
D(CRD5) = DATSET/FA(PLN3), ZDIR, ZORIG, FA(LN4), XDIR, YORIG, FA(PT2), XORIG
D(CRD5) = TRANS/ZORIG, -0, YORIG, -0, XORIG, -0
SNSET/APPRCH, 2.0000
SNSET/RETRCT, 2.0000
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, FA(PLN3), 20
$$精建零件坐标系
F(DATUMA)=FEAT/PLANE,CART,32.2571,24.7500,-0.0000,0.0000,0.0000,1.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, -3.0000, 4.0319, 21.0000
MEAS/PLANE, F(DATUMA), 12
  GOTO/CART,   -3.0000,  4.0319, 21.0000
  GOTO/CART,    4.4295, 10.7417, 21.0000
  PTMEAS/CART,  4.4295, 10.7417,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART,  2.8236, 57.1961,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 21.9873, 83.8374,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 39.5331, 90.2637,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 60.6679, 66.8592,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 60.4297, 40.2056,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 59.0728, 22.6212,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 44.5245, 30.9028,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 16.6222, 31.5880,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 17.8041,  8.9698,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 40.9138,  6.6601,  0.0000, 0.0000, 0.0000, 1.0000
  PTMEAS/CART, 62.9500,  5.5652,  0.0000, 0.0000, 0.0000, 1.0000
ENDMES
D(CRD6) = DATSET/FA(DATUMA), ZDIR, ZORIG
D(CRD6) = TRANS/ZORIG, -0
F(DATUMB)=FEAT/LINE,BND,CART,2.0000,0.0000,-0.0000,64.5143,0.0000,-0.0000,0.0000,-1.0000,0.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 62.9500, 5.5652, 21.0000
MEAS/LINE, F(DATUMB), 6
  GOTO/CART,   62.9500,  5.5652, 21.0000
  GOTO/CART,    5.0000, -3.0000, 21.0000
  PTMEAS/CART,  5.0000,  0.0000, -3.0000, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 16.3029,  0.0000, -3.0000, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 27.6057,  0.0000, -3.0000, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 38.9086,  0.0000, -3.0000, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 50.2114,  0.0000, -3.0000, 0.0000, -1.0000, 0.0000
  PTMEAS/CART, 61.5143,  0.0000, -3.0000, 0.0000, -1.0000, 0.0000
ENDMES
F(DATUMC)=FEAT/LINE,BND,CART,0.0000,2.0000,-0.0000,0.0000,61.3660,-0.0000,-1.0000,0.0000,0.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 61.5143, -3.0000, 21.0000
MEAS/LINE, F(DATUMC), 6
  GOTO/CART,   61.5143, -3.0000, 21.0000
  GOTO/CART,   -3.0000,  5.0000, 21.0000
  PTMEAS/CART,  0.0000,  5.0000, -3.0000, -1.0000, 0.0000, 0.0000
  PTMEAS/CART,  0.0000, 15.6732, -3.0000, -1.0000, 0.0000, 0.0000
  PTMEAS/CART,  0.0000, 26.3464, -3.0000, -1.0000, 0.0000, 0.0000
  PTMEAS/CART,  0.0000, 37.0196, -3.0000, -1.0000, 0.0000, 0.0000
  PTMEAS/CART,  0.0000, 47.6928, -3.0000, -1.0000, 0.0000, 0.0000
  PTMEAS/CART,  0.0000, 58.3660, -3.0000, -1.0000, 0.0000, 0.0000
ENDMES
F(PT_INTER2)=FEAT/POINT,CART,0.0000,0.0000,-0.0000,0.0000,0.0000,1.0000
CONST/POINT,F(PT_INTER2),INTOF,FA(DATUMB),FA(DATUMC)
D(CRD7) = DATSET/FA(DATUMA), ZDIR, ZORIG, FA(DATUMB), XDIR, FA(PT_INTER2), XORIG
D(CRD7) = TRANS/ZORIG, -0, YORIG, FA(PT_INTER2), XORIG, -0
F(DATUMA)=FEAT/PLANE,CART,32.2571,24.7500,-0.0000,0.0000,0.0000,1.0000
F(DATUMB)=FEAT/LINE,BND,CART,2.0000,0.0000,-0.0000,64.5143,0.0000,-0.0000,0.0000,-1.0000,0.0000
F(DATUMC)=FEAT/LINE,BND,CART,0.0000,2.0000,-0.0000,0.0000,61.3660,-0.0000,-1.0000,0.0000,0.0000
F(点-1)=FEAT/POINT,CART,3.4927,57.9454,-0.0000,0.0000,0.0000,1.0000
F(点-2)=FEAT/POINT,CART,4.8316,9.6844,-0.0000,0.0000,0.0000,1.0000
F(点-3)=FEAT/POINT,CART,58.1595,6.5933,-0.0000,0.0000,0.0000,1.0000
F(点-4)=FEAT/POINT,CART,59.9509,70.8109,-0.0000,0.0000,0.0000,1.0000
F(点-5)=FEAT/POINT,CART,32.8954,94.3379,-0.0000,0.0000,0.0000,1.0000
F(点-6)=FEAT/POINT,CART,21.9919,48.8640,-0.0000,0.0000,0.0000,1.0000
F(点-7)=FEAT/POINT,CART,22.6138,19.4703,-0.0000,0.0000,0.0000,1.0000
F(点-8)=FEAT/POINT,CART,44.4903,31.1281,-0.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 3.4927, 57.9454, 3.0000
MEAS/POINT, F(点-1), 1
  GOTO/CART, 3.4927,57.9454,21.0000
  PTMEAS/CART, 3.4927,57.9454,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 4.8316, 9.6844, 3.0000
MEAS/POINT, F(点-2), 1
  GOTO/CART, 4.8316,9.6844,21.0000
  PTMEAS/CART, 4.8316,9.6844,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 58.1595, 6.5933, 3.0000
MEAS/POINT, F(点-3), 1
  GOTO/CART, 58.1595,6.5933,21.0000
  PTMEAS/CART, 58.1595,6.5933,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 59.9509, 70.8109, 3.0000
MEAS/POINT, F(点-4), 1
  GOTO/CART, 59.9509,70.8109,21.0000
  PTMEAS/CART, 59.9509,70.8109,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 32.8954, 94.3379, 3.0000
MEAS/POINT, F(点-5), 1
  GOTO/CART, 32.8954,94.3379,21.0000
  PTMEAS/CART, 32.8954,94.3379,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 21.9919, 48.8640, 3.0000
MEAS/POINT, F(点-6), 1
  GOTO/CART, 21.9919,48.8640,21.0000
  PTMEAS/CART, 21.9919,48.8640,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 22.6138, 19.4703, 3.0000
MEAS/POINT, F(点-7), 1
  GOTO/CART, 22.6138,19.4703,21.0000
  PTMEAS/CART, 22.6138,19.4703,-0.0000,0.0000,0.0000,1.0000
ENDMES
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 44.4903, 31.1281, 3.0000
MEAS/POINT, F(点-8), 1
  GOTO/CART, 44.4903,31.1281,21.0000
  PTMEAS/CART, 44.4903,31.1281,-0.0000,0.0000,0.0000,1.0000
ENDMES
F(GR-1)=FEAT/POINT,CART,72.2870,13.9737,-5.0102
以上是关于RationalDMIS2022阵列工件测量的主要内容，如果未能解决你的问题，请参考以下文章
 

 三坐标检测之坐标系建立原则及分类


 机器视觉实验三    工件尺寸和面积测量


 三坐标测量仪如何建立坐标系


 考证不易，小王叹气


 NETDMIS5.0脱机编程指导2023


 RationalDMIS 2020测量平面