Flannel IPIP 跨节点通信

Posted 2022-06-07 whale_life

Flannel IPIP 模式安装部署

IPIP 类型的隧道是最简单的一种。它的开销最低，但只能封装 ipv4 单播通信，因此无法设置 OSPF、 RIP 或任何其他基于多播的协议。

部署 ipip 模式，只需要将 ​​"Type": "vxlan"​​​ 更换为 ​​"Type": "ipip"​​

如果需要在同一个二层类似于 host-gw 的效果，那么可以将 ​​DirectRouting​​ 配置为 true。

wget https://raw.githubusercontent.com/flannel-io/flannel/master/Documentation/kube-flannel.yml

sed -i "s/vxlan/ipip/g" kube-flannel.yml

跨节点通信

[root@master <sub>]# kubectl create deployment cni-test --image=burlyluo/nettoolbox --replicas=2
[root@master </sub>]# kubectl get pod -o wide 
NAME                        READY   STATUS              RESTARTS   AGE   IP       NODE              NOMINATED NODE   READINESS GATES
cni-test-777bbd57c8-jl2bh   0/1     ContainerCreating   0          5s    <none>   node1.whale.com   <none>           <none>
cni-test-777bbd57c8-p5576   0/1     ContainerCreating   0          5s    <none>   node2.whale.com   <none>           <none>

pod1 信息

[root@master <sub>]# kubectl exec -it cni-test-777bbd57c8-jl2bh -- bash
bash-5.1# ifconfig eth0
eth0      Link encap:Ethernet  HWaddr EA:BC:22:E6:7A:FA  
          inet addr:10.244.1.2  Bcast:10.244.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1480  Metric:1
          RX packets:13 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1178 (1.1 KiB)  TX bytes:42 (42.0 B)

bash-5.1# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         10.244.1.1      0.0.0.0         UG    0      0        0 eth0
10.244.0.0      10.244.1.1      255.255.0.0     UG    0      0        0 eth0
10.244.1.0      0.0.0.0         255.255.255.0   U     0      0        0 eth0
bash-5.1# ethtool -S eth0
NIC statistics:
     peer_ifindex: 7
     rx_queue_0_xdp_packets: 0
     rx_queue_0_xdp_bytes: 0
     rx_queue_0_xdp_drops: 0



[root@node1 </sub>]# ip link show | grep ^7
7: vethb74d434d@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1480 qdisc noqueue master cni0 state UP mode DEFAULT group default 
[root@node1 <sub>]# ip link show vethb74d434d
7: vethb74d434d@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1480 qdisc noqueue master cni0 state UP mode DEFAULT group default 
    link/ether fe:b1:c5:f4:d0:b2 brd ff:ff:ff:ff:ff:ff link-netnsid 0
[root@node1 </sub>]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.0.1     0.0.0.0         UG    100    0        0 ens33
10.244.0.0      192.168.0.80    255.255.255.0   UG    0      0        0 flannel.ipip
10.244.1.0      0.0.0.0         255.255.255.0   U     0      0        0 cni0
10.244.2.0      192.168.0.82    255.255.255.0   UG    0      0        0 flannel.ipip
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
192.168.0.0     0.0.0.0         255.255.255.0   U     100    0        0 ens33
[root@node1 ~]# ip -d link show flannel.ipip
5: flannel.ipip@NONE: <NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN mode DEFAULT group default 
    link/ipip 192.168.0.81 brd 0.0.0.0 promiscuity 0 
    ipip remote any local 192.168.0.81 ttl inherit nopmtudisc addrgenmode eui64 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535

pod2 信息

[root@master <sub>]# kubectl exec -it cni-test-777bbd57c8-p5576 -- bash
bash-5.1# ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 06:D6:FD:BF:4C:02  
          inet addr:10.244.2.2  Bcast:10.244.2.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1480  Metric:1
          RX packets:13 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1178 (1.1 KiB)  TX bytes:42 (42.0 B)

bash-5.1# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         10.244.2.1      0.0.0.0         UG    0      0        0 eth0
10.244.0.0      10.244.2.1      255.255.0.0     UG    0      0        0 eth0
10.244.2.0      0.0.0.0         255.255.255.0   U     0      0        0 eth0
bash-5.1# ethtool -S eth0
NIC statistics:
     peer_ifindex: 7
     rx_queue_0_xdp_packets: 0
     rx_queue_0_xdp_bytes: 0
     rx_queue_0_xdp_drops: 0


[root@node2 </sub>]# ip link show | grep ^7
7: veth04bde23e@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1480 qdisc noqueue master cni0 state UP mode DEFAULT group default 
[root@node2 <sub>]# ip link show veth04bde23e
7: veth04bde23e@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1480 qdisc noqueue master cni0 state UP mode DEFAULT group default 
    link/ether 6e:67:70:7a:d2:51 brd ff:ff:ff:ff:ff:ff link-netnsid 0
[root@node2 </sub>]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.0.1     0.0.0.0         UG    100    0        0 ens33
10.244.0.0      192.168.0.80    255.255.255.0   UG    0      0        0 flannel.ipip
10.244.1.0      192.168.0.81    255.255.255.0   UG    0      0        0 flannel.ipip
10.244.2.0      0.0.0.0         255.255.255.0   U     0      0        0 cni0
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
192.168.0.0     0.0.0.0         255.255.255.0   U     100    0        0 ens33
[root@node2 ~]# ip -d link show flannel.ipip
5: flannel.ipip@NONE: <NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN mode DEFAULT group default 
    link/ipip 192.168.0.82 brd 0.0.0.0 promiscuity 0 
    ipip remote any local 192.168.0.82 ttl inherit nopmtudisc addrgenmode eui64 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535

跨节点通信数据流向图

抓包演示

pod1 10.244.1.2 node1

pod2 10.244.2.2 node2

[root@master ~]# kubectl exec -it cni-test-777bbd57c8-jl2bh -- ping -c 1 10.244.2.2

pod1.cap

[root@master ~]# kubectl exec -it cni-test-777bbd57c8-jl2bh -- tcpdump -pne -i eth0 -w pod1.cap

通过 pod 内部的路由表，我们可以确定，需要走网关 10.244.1.1 出去

通过查看 node1 上的 cni0 的地址，确定了网关地址。

pod1-ipip.cap

[root@node1 ~]# tcpdump -pne -i flannel.ipip -w pod1-ipip.cap

通过对 node1 路由表的分析，去往 pod2 的路由均指向了 ​​flannel.ipip​​ 网卡

再次查看，网卡为 ipip 设备，remote 封装的地址也都有，但是只封装 IP，没有 MAC 地址，为 RAW DATA。

通过对报文的分析，也可以确认为 RAW DATA

node1.cap

[root@node1 ~]# tcpdump -pne -i ens33 -w node1.cap

二层地址，直接 arp 就可以获取通信四元组

node2.cap

[root@node2 ~]# tcpdump -pne -i ens33 -w node2.cap

pod2-ipip.cap

[root@node2 ~]# tcpdump -pne -i flannel.ipip -w pod2-ipip.cap

pod2.cap

[root@master ~]# kubectl exec -it cni-test-777bbd57c8-p5576 -- tcpdump -pne -i eth0 -w pod2.cap