NETDMIS5.0对称度评价案例1

Posted

tags:

篇首语：本文由小常识网(cha138.com)小编为大家整理，主要介绍了NETDMIS5.0对称度评价案例1相关的知识，希望对你有一定的参考价值。


对称度用于控制被测要素中心平面（ 或中心线） 的共面（ 或共线） 性误差。

分类： 对称度包括直线（ 中心线） 对平面， 平面（ 中心面） 对平面， 直线（ 中心线） 与直线三种情况； 前两种情况下， 公差带均为对称于基准（ 直线或平面） 配置的两个平行平面之间的区域； 第三种情况下要求构成被测中心线的两条直线与基准直线在同一个平面内， 其公差带为对称于基准直线配置的两条平行直线之间的区域。

NETDMIS5.0对称度评价案例1_DMIS


1.首先测量圆柱，并把圆柱轴线设置成 Z 轴。

NETDMIS5.0对称度评价案例1_NETDMIS_02


NETDMIS5.0对称度评价案例1_NETDMIS_03


NETDMIS5.0对称度评价案例1_DMIS_04

MODE/MAN
DID(D2L40)=DEVICE/STOR,D2L40
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
SNSET/RETRCT,2.0000
SNSET/APPRCH,2.0000
GEOALG/CYLNDR,LSTSQR
F(圆柱1)=FEAT/CYLNDR,INNER,CART,0,0,-14.4057,0,0,1.00000000,30.0000,13.3907
MEAS/CYLNDR,F(圆柱1),8
PTMEAS/CART,-1.0697,14.9618,-14.0675,0.07131177,-0.99745407,0
PTMEAS/CART,14.9372,-1.3712,-14.3516,-0.99581299,0.09141385,0
PTMEAS/CART,-3.0110,-14.6947,-13.3458,0.20073153,0.97964629,0
PTMEAS/CART,-14.6749,3.1062,-14.4057,0.97832357,-0.20708209,0
PTMEAS/CART,-14.7542,2.7044,-1.1731,0.98361246,-0.18029568,0
PTMEAS/CART,-0.8725,14.9746,-1.0151,0.05816609,-0.99830692,0
PTMEAS/CART,13.8529,5.7531,-1.3366,-0.92352398,-0.38354069,0
PTMEAS/CART,4.6808,-14.2510,-1.2282,-0.31205047,0.95006553,0
ENDMES
DATDEF/F(圆柱1),DAT(A_圆柱1)
D(坐标系1_S)=DATSET/DAT(A_圆柱1),ZDIR
SAVE/DA(坐标系1)

2.采集被测要素(圆1与圆2），利用“圆1”和“圆2”构造一个中分点。

NETDMIS5.0对称度评价案例1_DMIS_05


NETDMIS5.0对称度评价案例1_NETDMIS_06

SNSET/DEPTH,0
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(XY),1
F(圆1)=FEAT/CIRCLE,INNER,CART,-20.0000,-26.0000,-1.2015,-0.02590842,-0.01299817,0.99957981,15.0000
MEAS/CIRCLE,F(圆1),4
PTMEAS/CART,-27.4807,-26.5373,-1.2015,0.99743025,0.07164426,0
PTMEAS/CART,-19.8884,-33.4992,-1.2015,-0.01487467,0.99988937,0
PTMEAS/CART,-12.8195,-23.8343,-1.2015,-0.95740323,-0.28875432,0
PTMEAS/CART,-20.0792,-18.5004,-1.2015,0.01055921,-0.99994425,0
ENDMES
SNSET/DEPTH,0
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(XY),1
F(圆2)=FEAT/CIRCLE,INNER,CART,20.0000,-26.0000,-1.4098,0.03086542,-0.05242839,0.99814758,15.0000
MEAS/CIRCLE,F(圆2),4
PTMEAS/CART,12.5876,-27.1428,-1.4098,0.98832205,0.15237957,0
PTMEAS/CART,17.8972,-18.8008,-1.4098,0.28037469,-0.95989064,0
PTMEAS/CART,27.4958,-26.2519,-1.4098,-0.99943601,0.03358072,0
PTMEAS/CART,20.2173,-33.4969,-1.4098,-0.02896680,0.99958037,0
ENDMES
F(点1)=FEAT/POINT,CART,0.0003,-26.0042,-1.3037,0,0,1.00000000
CONST/POINT,F(点1),MIDPT,FA(圆1),FA(圆2)

3.用中分点到基准A上做垂射点(把上面的中点垂射到圆柱轴线上)

NETDMIS5.0对称度评价案例1_NETDMIS_07

F(点2)=FEAT/POINT,CART,0,0,-1.3037,0.00001154,-1.00000000,0
CONST/POINT,F(点2),PROJPT,FA(点1),FA(圆柱1)

4.圆柱找正Z+，中分点和垂射点的连线绕Z+旋转到Y-，中分点确定X、
Y、Z的原点.

NETDMIS5.0对称度评价案例1_DMIS_08


NETDMIS5.0对称度评价案例1_NETDMIS_09


NETDMIS5.0对称度评价案例1_DMIS_10


5.构造坐标平面YZ

NETDMIS5.0对称度评价案例1_连线_11


NETDMIS5.0对称度评价案例1_DMIS_12


6.评价对称度

NETDMIS5.0对称度评价案例1_连线_13


NETDMIS5.0对称度评价案例1_连线_14

$$ NET_DMIS_20160720
$$ MADE IN DE 2023-2-9 12:59:58
INCLUD/DMIS,NET_DMIS_DEFINES.DMI
INCLUD/DMIS,VARDEFINE
DMESW/COMAND,PROBE_VAL/INIT
UNITS/MM,ANGDEC
D(MACHINE)=DATSET/MCS
DMESW/COMAND,COORDSYS/ALIGN
WKPLAN/XYPLAN
PRCOMP/ON
PRCOMP/ON
FEDRAT/POSVEL,MMPS,300.0000
ACLRAT/POSACL,MMPSS,100.0000
FEDRAT/MESVEL,MMPS,20.0000
ACLRAT/MESACL,MMPSS,100.0000
SNSET/RETRCT,1.0000
SNSET/SEARCH,5.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,SNSET/MANRETRCT,2
DMESW/COMAND,REPORT/CLEAR
MODE/MAN
DID(D2L40)=DEVICE/STOR,D2L40
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
SNSET/RETRCT,2.0000
SNSET/APPRCH,2.0000
GEOALG/CYLNDR,LSTSQR
F(圆柱1)=FEAT/CYLNDR,INNER,CART,0,0,-14.4057,0,0,1.00000000,30.0000,13.3907
MEAS/CYLNDR,F(圆柱1),8
PTMEAS/CART,-1.0697,14.9618,-14.0675,0.07131177,-0.99745407,0
PTMEAS/CART,14.9372,-1.3712,-14.3516,-0.99581299,0.09141385,0
PTMEAS/CART,-3.0110,-14.6947,-13.3458,0.20073153,0.97964629,0
PTMEAS/CART,-14.6749,3.1062,-14.4057,0.97832357,-0.20708209,0
PTMEAS/CART,-14.7542,2.7044,-1.1731,0.98361246,-0.18029568,0
PTMEAS/CART,-0.8725,14.9746,-1.0151,0.05816609,-0.99830692,0
PTMEAS/CART,13.8529,5.7531,-1.3366,-0.92352398,-0.38354069,0
PTMEAS/CART,4.6808,-14.2510,-1.2282,-0.31205047,0.95006553,0
ENDMES
DATDEF/F(圆柱1),DAT(A_圆柱1)
D(坐标系1_S)=DATSET/DAT(A_圆柱1),ZDIR
SAVE/DA(坐标系1)
SNSET/DEPTH,0
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(XY),1
F(圆1)=FEAT/CIRCLE,INNER,CART,-20.0000,-26.0000,-1.2015,-0.02590842,-0.01299817,0.99957981,15.0000
MEAS/CIRCLE,F(圆1),4
PTMEAS/CART,-27.4807,-26.5373,-1.2015,0.99743025,0.07164426,0
PTMEAS/CART,-19.8884,-33.4992,-1.2015,-0.01487467,0.99988937,0
PTMEAS/CART,-12.8195,-23.8343,-1.2015,-0.95740323,-0.28875432,0
PTMEAS/CART,-20.0792,-18.5004,-1.2015,0.01055921,-0.99994425,0
ENDMES
SNSET/DEPTH,0
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(XY),1
F(圆2)=FEAT/CIRCLE,INNER,CART,20.0000,-26.0000,-1.4098,0.03086542,-0.05242839,0.99814758,15.0000
MEAS/CIRCLE,F(圆2),4
PTMEAS/CART,12.5876,-27.1428,-1.4098,0.98832205,0.15237957,0
PTMEAS/CART,17.8972,-18.8008,-1.4098,0.28037469,-0.95989064,0
PTMEAS/CART,27.4958,-26.2519,-1.4098,-0.99943601,0.03358072,0
PTMEAS/CART,20.2173,-33.4969,-1.4098,-0.02896680,0.99958037,0
ENDMES
F(点1)=FEAT/POINT,CART,0.0003,-26.0042,-1.3037,0,0,1.00000000
CONST/POINT,F(点1),MIDPT,FA(圆1),FA(圆2)
F(点2)=FEAT/POINT,CART,0,0,-1.3037,0.00001154,-1.00000000,0
CONST/POINT,F(点2),PROJPT,FA(点1),FA(圆柱1)
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(XY),1
F(直线1)=FEAT/LINE,UNBND,CART,0,0,-1.3037,0.00001154,-1.00000000,0,1.00000000,0.00001154,0
CONST/LINE,F(直线1),BF,FA(点2),FA(点1)
DATDEF/F(圆柱1),DAT(A_圆柱1)
D(坐标系2_S)=DATSET/DAT(A_圆柱1),ZDIR
D(坐标系2_R)=ROTATE/ZAXIS,FA(直线1),-YDIR
D(坐标系2_T)=TRANS/XORIG,FA(点2),YORIG,FA(点2),ZORIG,FA(点2)
DMESW/COMAND,COORDSYS/CAD=PART
SAVE/DA(坐标系2)
F(平面1)=FEAT/PLANE,CART,0,0,0,1.00000000,0,0
F(圆3)=FEAT/CIRCLE,INNER,CART,-20.0000,-26.0000,0,0,0,1.00000000,15.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆3),CIRCLE,INNER,CART,LSTSQR,-20.0000,-26.0000,$
0,0,0,1.00000000,15.0000,-1.00000000,0,0,4,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"",FALSE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,0,0,0,0,3.0000,0,10,0,1,0,5.0000,$
"EXT3",ENDCAL
F(圆4)=FEAT/CIRCLE,INNER,CART,20.0000,-26.0000,0,0,0,1.00000000,15.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆4),CIRCLE,INNER,CART,LSTSQR,20.0000,-26.0000,$
0,0,0,1.00000000,15.0000,-1.00000000,0,0,4,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"",FALSE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,0,0,0,0,3.0000,0,10,0,1,0,5.0000,$
"EXT3",ENDCAL
T(对称度1)=TOL/SYM,0.0500,FA(平面1),RFS
DMESW/COMAND,OUTPUT/UNIT,DIMENSION/MM
OUTPUT/FA(圆3),FA(圆4),TA(对称度1)

注意事项：1.区分被测要素与基准要素；
2.基准只能是直线或者平面，一般为构造的特征（例如中分线、中分面等）；
3.被测元素在测量时， 要求在构成被测中心要素（ 直线或平面） 的两个轮廓要素（ 直线或平面） 上采相同数量的测量点。
4.当这两个轮廓要素（ 直线或平面） 不平行时， 还进一步要求两侧轮廓要素（ 直线或平面）上相对应的测点间的连线应垂直与其中心要素（ 直线或平面） 。（被测面至少4个点,点5，6，7，8最好采用镜像的特征,然后切换到DCC自动运行一遍。）


NETDMIS5.0边界点检测2023


在模型上获得薄壁件的理论数据以便测量薄壁件的变形情况。 （ 一次只获得一个边缘点的坐标）

NETDMIS5.0边界点检测2023_NETDMIS


边界点适用于测量棱边的检测，常用于钣金件边缘的检测。

NETDMIS5.0边界点检测2023_DMIS_02


NETDMIS5.0边界点检测2023_算法_03

NETDMIS5.0边界点检测2023_算法_04


“ 模式” ： 辅助点的测点数设置。 一个点辅助面测量一个点， 确定了边缘点的实际深度；两个点测量一条线， 确定了边缘点的实际深度和边缘点在其截面上的矢量方向； 三个点测量一个平面， 确定了边缘点的实际深度和边缘点的矢量方向。

NETDMIS5.0边界点检测2023_NETDMIS_05


NETDMIS5.0边界点检测2023_算法_06

$$ NET_DMIS_20160720
$$ MADE IN DE 2023-2-23 9:25:24
INCLUD/DMIS,NET_DMIS_DEFINES.DMI
INCLUD/DMIS,VARDEFINE
DMESW/COMAND,PROBE_VAL/INIT
UNITS/MM,ANGDEC
D(MACHINE)=DATSET/MCS
DMESW/COMAND,COORDSYS/ALIGN
WKPLAN/XYPLAN
PRCOMP/ON
PRCOMP/ON
FEDRAT/POSVEL,MMPS,300.0000
ACLRAT/POSACL,MMPSS,100.0000
FEDRAT/MESVEL,MMPS,20.0000
ACLRAT/MESACL,MMPSS,100.0000
SNSET/RETRCT,1.0000
SNSET/SEARCH,5.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,SNSET/MANRETRCT,1.0000
DMESW/COMAND,REPORT/CLEAR
MODE/MAN
DID(D2L40)=DEVICE/STOR,D2L40
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
FEDRAT/MESVEL,MMPS,2.0000
SNSET/RETRCT,2.0000
SNSET/APPRCH,2.0000
DMESW/COMAND,SNSET/MANRETRCT,2.0000
GEOALG/PLANE,LSTSQR
F(平面1)=FEAT/PLANE,CART,31.2650,39.5919,0,0,0,1.00000000
MEAS/PLANE,F(平面1),4
PTMEAS/CART,3.7540,55.2894,0,0,0,1.00000000
PTMEAS/CART,2.7995,4.3170,0,0,0,1.00000000
PTMEAS/CART,60.3669,5.1633,0,0,0,1.00000000
PTMEAS/CART,58.1395,93.5981,0,0,0,1.00000000
ENDMES
SNSET/DEPTH,0
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(平面1),1
F(直线1)=FEAT/LINE,UNBND,CART,3.6651,0,-2.2385,0.99998102,0,-0.00616102,0,-1.00000000,0
MEAS/LINE,F(直线1),2
PTMEAS/CART,3.6651,0,-2.4232,0,-1.00000000,0
PTMEAS/CART,63.6273,0,-2.4232,0,-1.00000000,0
ENDMES
F(点1)=FEAT/POINT,CART,0,4.3945,-2.5726,-1.00000000,0,0
MEAS/POINT,COMP,DME,F(点1),1
PTMEAS/CART,0,4.3945,-2.5726,-1.00000000,0,0
ENDMES
DATDEF/F(平面1),DAT(A_平面1)
D(坐标系1_S)=DATSET/DAT(A_平面1),ZDIR
D(坐标系1_R)=ROTATE/ZAXIS,FA(直线1),XDIR
D(坐标系1_T)=TRANS/ZORIG,FA(平面1)
D(坐标系1_T)=TRANS/YORIG,FA(直线1)
D(坐标系1_T)=TRANS/XORIG,FA(点1)
DMESW/COMAND,COORDSYS/CAD=PART
SAVE/DA(坐标系1)
MODE/AUTO,PROG,MAN
SNSET/RETRCT,1.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,CLEARP/ZDIR,10.0000,ZDIR,10.0000,ON
F(平面2)=FEAT/PLANE,CART,32.4057,47.9193,0,0,0,1.00000000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_PLANEPOINTS_1006),AUTOFIGURE,F(平面2),PLANE,CART,LSTSQR,32.4057,47.9193,$
0,0,0,1.00000000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,POINTS,9,2.4645,6.4585,0,0,0,1.00000000,3.1419,$
59.2458,0,0,0,1.00000000,22.8566,94.6659,0,0,0,1.00000000,58.4447,96.4369,0,0,0,1.00000000,61.7202,66.2279,$
0,0,0,1.00000000,60.3207,4.3748,0,0,0,1.00000000,21.8357,6.4613,0,0,0,1.00000000,20.9073,50.4742,0,0,$
0,1.00000000,39.9595,46.9280,0,0,0,1.00000000,TOUCH,0.3000,XYPLAN
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,CONST/SET_PROJ_VEC,FA(XY),1
F(圆8)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,-3.0000,0,0,1.00000000,36.0000
CONST/CIRCLE,F(圆8),BF,FA(圆2),FA(圆3),FA(圆4),FA(圆5),FA(圆6),FA(圆7)
F(直线2)=FEAT/LINE,BND,CART,4.0000,0,-2.0000,63.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线2),LINE_BND,CART,4.0000,0,-2.0000,1.00000000,$
0,0,59.0000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,0,-1.00000000,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,LINE,$
"","","EXT1","EXT2","EXT3",ENDCAL
F(直线3)=FEAT/LINE,BND,CART,0,4.0000,-2.0000,0,58.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线3),LINE_BND,CART,0,4.0000,-2.0000,0,1.00000000,$
0,54.0000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,-1.00000000,0,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,LINE,"",$
"","EXT1","EXT2","EXT3",ENDCAL
F(点2)=FEAT/POINT,CART,0,0,-2.0000,0,0,-1.00000000
CONST/POINT,F(点2),INTOF,FA(直线2),FA(直线3)
DATDEF/F(平面2),DAT(A_平面2)
D(坐标系2_S)=DATSET/DAT(A_平面2),ZDIR
D(坐标系2_R)=ROTATE/ZAXIS,FA(直线2),XDIR
D(坐标系2_T)=TRANS/XORIG,FA(点2),YORIG,FA(点2)
D(坐标系2_T)=TRANS/ZORIG,FA(平面2)
SAVE/DA(坐标系2)
F(圆1)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,0,0,0,1.00000000,20.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆1),CIRCLE,INNER,CART,LSTSQR,31.5000,31.5000,$
0,0,0,1.00000000,20.0000,-1.00000000,0,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,$
FALSE,FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,$
5.0000,"EXT3",ENDCAL
F(圆2)=FEAT/CIRCLE,INNER,CART,31.5000,49.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆2),CIRCLE,INNER,CART,LSTSQR,31.5000,49.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,$
FALSE,FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,$
5.0000,"EXT3",ENDCAL
F(圆3)=FEAT/CIRCLE,INNER,CART,15.9115,40.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆3),CIRCLE,INNER,CART,LSTSQR,15.9115,40.5000,$
0,0,0,1,10.0000,-0.5,-0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,5.0000,$
"EXT3",ENDCAL
F(圆4)=FEAT/CIRCLE,INNER,CART,15.9115,22.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆4),CIRCLE,INNER,CART,LSTSQR,15.9115,22.5000,$
0,0,0,1,10.0000,0.5,-0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,5.0000,$
"EXT3",ENDCAL
F(圆5)=FEAT/CIRCLE,INNER,CART,31.5000,13.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆5),CIRCLE,INNER,CART,LSTSQR,31.5000,13.5000,$
0,0,0,1,10.0000,1,0,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,FALSE,0,"CUR",$
TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,5.0000,"EXT3",ENDCAL
F(圆6)=FEAT/CIRCLE,INNER,CART,47.0885,22.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆6),CIRCLE,INNER,CART,LSTSQR,47.0885,22.5000,$
0,0,0,1,10.0000,0.5,0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,5.0000,$
"EXT3",ENDCAL
F(圆7)=FEAT/CIRCLE,INNER,CART,47.0885,40.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆7),CIRCLE,INNER,CART,LSTSQR,47.0885,40.5000,$
0,0,0,1,10.0000,-0.5,0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",7,1,0,0,0,3.0000,0,10,0,1,0,5.0000,$
"EXT3",ENDCAL
F(点3)=FEAT/POINT,CART,81.2846,48.0055,-12.8864,0.52044052,0,0.85389793
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点3),POINT,CART,DME,81.2846,48.0055,-12.8864,$
0.52044052,0,0.85389793,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,1,FA(VECBLD),2.0000,2.5000,3,$
XYPLAN,"","EXT1","EXT2","EXT3",ENDCAL
F(边缘点1)=FEAT/EDGEPT,CART,13.7088,85.0449,0,-0.86542734,0.50103446,0,0,0,1.00000000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINTEDGE_1006),AUTOFIGURE,F(边缘点1),EDGEPT,CART,13.7088,85.0449,0,-0.86542734,$
0.50103446,0,0,0,0,0,1.00000000,2.0000,2.0000,5.0000,5.0000,3,1.0000,XYPLAN
F(边缘点2)=FEAT/EDGEPT,CART,8.3980,75.8718,0,-0.86542734,0.50103446,0,0,0,1.00000000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINTEDGE_1006),AUTOFIGURE,F(边缘点2),EDGEPT,CART,8.3980,75.8718,0,-0.86542734,$
0.50103446,0,0,0,0,0,1.00000000,2.0000,2.0000,5.0000,5.0000,2,1.0000,XYPLAN


以上是关于NETDMIS5.0对称度评价案例1的主要内容，如果未能解决你的问题，请参考以下文章

发动机气缸的圆柱度和园度误差各是指啥。。。

基于 MATLAB 的圆柱度误差评定方法

NETDMIS5.0边界点检测2023

360视频：赤道圆柱投影ECP

UG怎么建基准平面

2022-08-26 Unity视频播放4——全景视频